Jump to content

This Could Be Titanic, I've Just Run Into A Rebberg!

clockwatcher
 Share

Recommended Posts

clockwatcher WRT Addict

clockwatcher

Posted
Posted

Evenin' all!

 

A little earlier, by way of relaxation, I opened up my box of assorted watch parts. I bought a small job lot of bits from the Bay place about a month ago but haven't really properly scrutinised everything that came. Thus it was, as I studied the various movements with a loupe that I found a largely complete movement with the mark 'REBBERG DEPOSE'.

 

Naturally, I Googled this and found not a lot but there was a reference to Rebberg and Rolex in one particular article. Heart skips beat!

 

In a item in the Rolex Magazine Blogspot I found this illustration:

post-742-0-74790900-1430945484_thumb.jpg

 

If you compare that illustration with a pic I just took of my movement you'll see the similarities, albeit that mine is differently handed - not quite a mirror image. Clearly mine is missing the barrel wheel and screw that might have had the Rolex name on it. Bah! Also a couple of bridge screws.

post-742-0-52166100-1430946082_thumb.jpg

 

 

The dial side is lacking the 'wheel in the middle' whatever it's properly called but the keyless work seems complete.

post-742-0-24701400-1430945749_thumb.jpg

 

Does anyone have any further info about Rebbergs and an insight into how likely it is that this might be an early Rolex. I'm grasping at straws here I know but what fun if it were!

 

Cheers

John

 

 

Link to comment
Share on other sites
clockwatcher WRT Addict

clockwatcher

Posted
  • Author
Posted

Thanks Will, that's interesting. I think mine would benefit from a good clean and a little scratch removal on the train side. Maybe this can be my first cleaning effort using the Brenray. I have my uncle's gold Bulova case and bracelet to do before I get it down to the jeweller for appraisal so they could go for a bath together.

The Bulova has an inexpensive quartz movement but, with a very nice 14k bracelet, should be worth a bob or two. I don't think that it will have any greater value simply as a watch.

Another item in my job lot turned out to be a Slava 2428 movement, or most of one anyway. Found a few online that look quite attractive but they don't seem to be very expensive. Like my favourite Favres the 2428 has a twin-barrel arrangement, so interesting from the technical standpoint.

Link to comment
Share on other sites
clockwatcher WRT Addict

clockwatcher

Posted
  • Author
Posted

Roberto, yes, **BLEEP** criminal! That may explain why he nicked the barrel wheel, which might have given a clue to the watch brand.

I may be able to remove the signs of surgery but restoring the pearling/engine turning will be a bit tricky. Any tips anyone?

What IS the name of the 'wheel-in-the-middle' on the dial side? It might help to know when it comes to searching a replacement out.

Link to comment
Share on other sites
Michael WRT Addict

Michael

Posted
Posted

Hi Clockwatch, I really like wrist watches from this era. I have a couple of Rebberg's which I thought you might like to see, which are not one's that were sold to Rolex. The cases are marked Rebberg, and one was branded by Lancet. You will see the movement was also marked Rebberg. I am pretty sure your find is a Rebberg that was sold to Rolex and the ratchet wheel would have been marked with Rolex branding. It is a nice find, even if only for spares 

post-143-0-84327900-1431153787_thumb.jpg

post-143-0-11376500-1431153792_thumb.jpg

post-143-0-17593600-1431153799_thumb.jpg

post-143-0-98642000-1431153804_thumb.jpg

  • Like 2
Link to comment
Share on other sites
  • 8 years later...

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Restore formatting

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

×
 Share
Go to topic listing


  • Recently Browsing

    • No registered users viewing this page.

  • Topics

  • Posts

    • ManSkirtBrew
      Accutron 218 transistors

      By ManSkirtBrew · Posted

      As is tradition, one step forward, two steps back. Got the board populated and soldered into place without any issues.   But no hum. So I started testing the coils with an ohmmeter. I got 5.84k ohms across D1 (from red to red in the picture below), which is as expected. But I'm getting an open circuit for the other drive coil and feedback coil, D2 and F1 (from green to each of the two yellows).   Since the movement was working with my breadboard setup, it implies I somehow broke the connection between the coils and the solder lugs. They're all the way at the bottom of the lugs, but maybe the heat migrated down and broke the connections? I guess it's possible it happened while cleaning the flux off, but I used a soft artist's brush and isopropyl alcohol. I did a lot of high magnification examination, and I don't see any issues, but let me know if you see anything I missed or if you can think of anything else I should check.
    • GuyMontag
      Watch of Today

      By GuyMontag · Posted

      1947 NOS Ambassador 'C'. Actually, the case came without the movement so the movement isn't NOS, but she sure is pretty.
    • watchweasol
      AS2063 - hand setting

      By watchweasol · Posted

      Hi attached is the AS 20XX. Service sheet although there is no 2063 mentioned it may be of some use to you AS_AS 2060,1,2,6,4,6.pdf
    • JohnR725
      Epilame / Fixodrop

      By JohnR725 · Posted

      one of the problems we have is visible versus invisible. For instance millennium disulfide another high pressure lubricant black in color. I was told by somebody worked for the Boeing company that they had a piston like device somewhere that has eight call it around it to grab it so it has to slide and in the collet has to grab. But if somebody puts that type of dry grease on where grease with that in it it embeds itself basically in the metal and they have to throw the whole part away they get use it all. So I suspect on all the dry powdery lubricants that they will go into all the basically microscopic cracks and crannies of the metaland that's where it is visually at least until you scrub it off your visually going to see it which is good because you want your lubrication the stay word is. But I'm sure it doesn't last forever on the metal it's just a really nice lubrication  
    • GuyMontag
      Seiko 6601 Tech Sheet?

      By GuyMontag · Posted

      Thanks for the info. I can't seem to find tech sheets for those either.  I'll muddle my way though 🙂
×
×
  • Create New...