Jump to content

Hello from Dunstable

Mike1980

By Mike1980
in Introduce Yourself Here

 Share

Recommended Posts

Mike1980 Member

Mike1980

Posted
Posted

Hi all,

Been interested in Watches for the past few years, then I started to get interested in how they actually worked.

After chatting with a guy from a shop I bought a Watch from, I then started getting a bit carried away on eBay. I have now accumulated a fair number of various Pocket Watches, Tools and Books, it has now become my favourite hobby.

I’m looking forward to learning and honing my skills and thought this Forum must be a great place to start

Thanks, 

Mick

 

Link to comment
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Restore formatting

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

×
 Share
Go to topic listing


  • Recently Browsing

    • No registered users viewing this page.

  • Topics

  • Posts

    • djwilliams37
      Rotary skeleton part identification

      By djwilliams37 · Posted

      Thanks for your most appreciated assessment with this. I will purchase a new movement. 
    • Terrinecold
      First movement = First broken movement

      By Terrinecold · Posted

      Sorry I am confused by step 4. Which screw? There is the balance cock screw. I don’t think that is what you are talking about. The only other screw I see is on the side of the swan neck regulator. I do t think that is the one you are talking about either Well I managed to make it worse again but I could take pictures.  I had put the balance cock partially in place with one locator pin in. I wanted to remove it and I know I should use my screwdriver in the slot to move it off the pin but I didn’t l pulled wit my tweezers and it stuck then gave suddenly and was thrown a few inches away and of course the hairspring got tangled (a coil was above the cock) and untangling it from the cock deformed it.    I am going to try to put it back in shape and I will likely post more pictures after shortly. I’ll wait for feedback before reattaching it to the cock I am sorry I think I’ll give up. I was trying to remove the tangle. I had previously succeeded but now I just made more of a mess with this new tangle.  Lf you see my spring it is now just a knot. 
    • RichardHarris123
      Hello!

      By RichardHarris123 · Posted

      Hello and welcome from Leeds, England. 
    • nevenbekriev
      First movement = First broken movement

      By nevenbekriev · Posted

      OK, bad video... Almost all of them are. To attach the spring (stud) to the cock: 1. Put the cock on the table top upside down.  Open the regulator if closed. 2. Put the balance on , align the stud above the hole for it in the stud carrier. 3. Help the stud to get in the hole by gentle pressing. 4. When it is in, grasp the cock with balance with tweezers (from aside, not from above), then get it between fingers, not changing the horizontal position, then tighten slightly the screw. This is the moment to correct the high position of the stud - it's top must be even with the carrier. Now tighten the screw. 5. If the outer coil is out of the regulator, move the regulator to the max to '+' position, then guide the spring to get in the regulator. Now You can return the regulator where it was and close it above the spring
    • Ranger579
      Hello!

      By Ranger579 · Posted

      Newly interested in watch servicing & repair.  Just ordered a few basic tools and a cheap Seagull movement to practice on.  I hope this turns out to be a rewarding hobby (intellectually, not financially.  Really not expecting financially 🙂).  Just wanted to say hi and no doubt I'll be back for advice.
×
×
  • Create New...