Jump to content

Decent Watch Bands In The U.s.


Recommended Posts

Can anyone recommend a supplier of decent watch bands in the U.S.?  I ordered one from Esslinger and this is what happened the SECOND TIME I put it on:

 

post-752-0-78839300-1428427062_thumb.jpg

 


I don't necessarily need top of the line licked by kittens and blessed by angels quality.  Just something that will hold up.

Link to comment
Share on other sites

licked by kittens and blessed by angels quality

...

That's too funny! :) In any case, have you tried ofrei? I believe their quality is a bit better, some are the same though!

 

Cheers,

 

Bob

Link to comment
Share on other sites

  • 2 weeks later...

Just wondering about selecting the correct size for this band.  The crappy band was an 18 mm and as you can see it is a bit smooshed.  The next standard size seems to be 16 mm.

 

I measure the width between lugs on this watch to be 17.43 mm.  What is the right choice for this measurement?

Link to comment
Share on other sites

If we complicate it ? The right size for your watch should be a 11/16 . That is 17,43 mm . There are straps out there in that size . But i would go for a nice 18 mm strap . From Hirsch och Rios . Rios has some very nice straps . 

Link to comment
Share on other sites

I'm surprised with that failure. I've had good quality from Esslinger. They will refund with no hassle though. They also carry a line of 17mm bands. I would go for one of those. I did for a vintage Elgin and am very happy with it.

 

Good luck,

Stu

Edited by Gotwatch
Link to comment
Share on other sites



  • Recently Browsing

    • No registered users viewing this page.
  • Topics

  • Posts

    • The part was how it fell out of the movement - the train wheel bridge wasn’t screwed in.    I’ll probably dismantle the part, if I can, to work it out.    The train of wheels ran fine - it was only once the keyless works were installed I noticed the problem. 
    • Hello, I am about 5 months into watchmaking and I love it!   The attention to precise detail is what really attracts me to it. (and the tools!) I am working on a 16 jewel 43mm pocket watch movement.   There are no markings besides a serial number (122248) .  The balance staff needs replacement. The roller side pivot broke off.  I successfully removed the hairspring using Bergeon 5430's.  I successfully removed the roller using Bergeon 2810.   Did i mention I love the tools?! I removed the staff from the balance wheel using a vintage K&D staff removal tool  with my Bergeon 15285 (that's the one that comes with a micrometer adjustment so it can be used as a jewel press as well as a traditional staking tool...it's sooooo cool...sorry..  can you tell i love the tools?) No more digressing..  I measured the damaged staff in all the relevant areas but I have to estimate on some because one of the pivots is missing. A = Full length  A= 4.80mm  (that's without the one pivot...if you assume that the missing pivot is the same length as the other pivot (I'm sure it's not)  then A = 5.12 mm...(can I assume 5.00mm here?) F=  Hair spring collet seat  F=  .89mm   (safe to assume .90 here? .. I am sure that my measurement's would at least contain  .01 mm error ?) G = balance wheel seat  G = 1.23 mm  (1.20mm?) H  =  roller staff  H =  .59mm  (.60 mm?) B  = bottom of the wheel to roller pivot   B  = 2.97mm  (3.00 mm?)     here I am estimating  again because this pivot is missing. So my friends, and I thank you profusely,  can you point me in the right direction as to how to proceed? Do i buy individual staffs?  or an assortment?   Since I don't know exactly the name of the manufacturer, will that be a fatal hindrance?   Tbh, I'm not even sure what country of origin this movement is. Thank you!    
    • Thats why i asked that question earlier, what happens if lubrication is placed directly on top of epilame ?  As opposed to walled within its non epilamed area . I'm not saying its right, i have no idea , just asking questions. 
    • thinking of where epilam should be removed did you know there was a patent that covers this? At least for the escapement I'm attaching it. GB1057607A-1 epilame.pdf
    • Back home...printing now.  Will report results
×
×
  • Create New...