Jump to content

Remove old screw down crown seal

familyguy

By familyguy
in Watch Repairs Help & Advice

 Share

Recommended Posts

familyguy Member

familyguy

Posted
Posted (edited)

I have a dive watch I purchased new, in the early 1970's with ETA auto wind movement, It's looking a bit sad and I would like to get serviced and looking nice again, it is I hope a good candidate as it was only ever serviced by a watchmaker, recently I tried to unscrew the crown, it was very stiff, when it came undone I noticed a black goo around the crown tube, looks as if the seal/o-ring has disintegrated, my question is how to get the goo out of the crown thread, is there a solvent I can soak it in. I did once have a winchester of benzene but was forced to get rid of it on pain of divorce - I'm sure benzene would have done it.

Edited by familyguy
Correct a typo
Link to comment
Share on other sites
  • familyguy changed the title to Remove old screw down crown seal
watchweasol Distinguished Member

watchweasol

Posted
Posted

Hi Ditto  old Hippy, having got a new crown then experiment removing the old goo the experience will come in handy for the future,   IPA, Ronsonol, benzine will probably do the trick, finding the correct cleaner will be handy as case back gaskets also get in this state.

Link to comment
Share on other sites
familyguy Member

familyguy

Posted
  • Author
Posted

Here are pics of the offending parts, movement is an ETA 2783, this is the first time I have removed the stem/crown and I notice that the square section of the stem has a twist in it - is this normal ? I'm assuming it is, as the watch was only ever serviced by a watchmaker and I doubt the stem could transmit enough force to twist the square section, I feel the the stem would break at the thread - the thinnest part.

20201213_095030.jpg

20201213_095107.jpg

20201213_095212.jpg

Link to comment
Share on other sites
jdm Distinguished Member

jdm

Posted
Posted
On 12/12/2020 at 4:39 AM, familyguy said:

I did once have a winchester of benzene but was forced to get rid of it on pain of divorce - I'm sure benzene would have done it.

I think you may have had benzine (motor petrol, gasoline) not benzene, the confusion is common among English speakers. Anyway the cleaning agent is not important because to replace the gasket in the crown you have to lift the top washer anyway, as said that's a bit of fiddly work but certainly doable. Or fit a new crown.

 

11 hours ago, familyguy said:

I notice that the square section of the stem has a twist in it - is this normal?

Yes it is, for period of time ETA was making movements with a twisted stem, probably with the idea these would help the clutch wheel pressing, then fortunately they stopped.

 

11 hours ago, rodabod said:

I reckon you may be able to get a matching replacement from cousins if you are based in Europe. 

Even if you're not, Cousins UK ships worldwide for the actual Royal Mail cost.

Link to comment
Share on other sites
 Share
Go to topic listing


  • Recently Browsing

    • No registered users viewing this page.

  • Topics

  • Posts

    • BFernandes
      Vendor selling small amount of Moebius oils. Legit?

      By BFernandes · Posted

      Thanks! I just need to find a decanter within the EU.
    • JohnR725
      Sellita SW 220 Hack issue

      By JohnR725 · Posted

      yes the end stones on the balance are flat on one side curved on the other. So yes curves side out unless you would like to reduce your end shake and have issues like you're having. Oh and minor technical problem the lift angles 50° according to the tech sheet. you dropped off a specification like the watch was fully wound up or its 24 hours later? So dial-up and dial down should be as close to identical as possible you have 221 and 215 maybe it's okay but it seems like they should be a little closer. Then as soon as you go to the crown positions dropping below 200.this is definitely a problem watch companies don't care about the maximum amplitude sort of in not supposed to go above 315° on this watch but at the end of 24 hours in the 6H  which is basically the 6 o'clock is up at the end of 24 hours it cannot go below 200° and basically all of your crown positions are unacceptable. Here is what the specifications are you will note that watch companies do not get obsessed with amplitudes like they do in this group. They only get obsessed with amplitudes at 24 hours for which this watch is unacceptable. although I'm assuming and I hate to do that that this watch is probably fully wound up and it 24 hours probably a miracle if the watch runs at all.
    • watchweasol
      12 O'Clock Never Strikes 12

      By watchweasol · Posted

      Also when you have it on the bench. Check that the rack is dropping the full amount and in the right place  on the snail.
    • oldhippy
      12 O'Clock Never Strikes 12

      By oldhippy · Posted

      I agree with clockboy. Just so you know what part is the snail here is a picture of a movement and I have marked the snail for you.
    • ColdWind
      Reversing wheels for ETA 2824 = SW200-1 and ETA 2892 = SW300-1

      By ColdWind · Posted

      My watchmaker friend once told me that you can swap reversing wheels between SW200 and ETA 2824 but NOT the whole bridge, just the wheels. I asked him that about parts interchangeability because I was working on a Maurice Lacroix with a rusted SW200's ball bearing. He said that he doesn't know about the bearing but I try swapping anyway, first I put the whole ETA rotor on the SW200 and it worked perfectly, so I punched the rusted bearing on the Maurice Lacroix rotor out and replaced it with ETA's. Since the bearing gear connects directly to the reversing wheels I say the wheels must be swappable. Don't know about 2892 and SW300 though, I never asked my friend about that. I wish someone out there with parts could spend their time to try swapping parts between various ETAs and SWs then make a compatible list, we the community would really appreciated it.
×
×
  • Create New...