Jump to content

Putting clock in beat

Willow

By Willow
in All Things Clocks

 Share

Recommended Posts

Willow WRT Addict

Willow

Posted
Posted

I have been having problems with setting the beat of a mantle clock when i move the pendulum the pallets does not move the escapement one tooth at a time no matter how much i adjust the pallets left right up down so i cant get it to tick tock. I did have it ticking for over a hour and striking ok then decided to put it back into its case and that was a performance i couldn't seem to get the brackets in the right position for the movement to be level  i did final do it then hey presto it  wouldn't tick  and have struggled the last couple of days with it,any advice would be grateful

Link to comment
Share on other sites
watchweasol Distinguished Member

watchweasol

Posted
Posted

Hi   the following  link will give you some tips .  https://www.horologica.co.uk/top/4_setup.html.   

I my self just let the pendulum stop and using a gauge mark the position, move it left and listen for the tick and mark the gauge  then from the center move right and again listen for the tock and mark. The distance from the centre to left and right should be the same, If not adjust the crutch in relation to the pallets/anchor to achieve this. If its ok and even then check the lockings of the pallet/anchor with the escape wheel, check the pallets/anchor for wear and its bearings for wear causing mis locking. The depth has to be right .

 

 

 

 

Link to comment
Share on other sites
oldhippy Distinguished Member

oldhippy

Posted
Posted

I think Hector is on the right track about the pallets. I think you have set the pallets to shallow so the depth needs to be a tiny bit lower. That is what I advise first. The pendulum needs to have a good swing. When the pallets are to shallow the pendulum will hardy swing. Could you check that first then get back to me. 

Link to comment
Share on other sites
Willow WRT Addict

Willow

Posted
  • Author
Posted

thank you for your replies the clock has been stripped down and oiled,will have a good look at the pallets again oldhippy and get back thanks. Had a look at the pallets which seem fine what a did noticed and missed before i had a look through a digital microscope, there is a chip at the end of the pivot on the pallet end

Link to comment
Share on other sites
Willow WRT Addict

Willow

Posted
  • Author
Posted

I am at my daughter's looking after her 2 grandchildren at the moment as soon as I get home I will try and send a picture but because it so small I don't if you will be able to see on the photo hope it won't be to long  so it might be tomorrow before I get the chance clocks are easier then 2 grandchildren :growl:

 

Link to comment
Share on other sites
Willow WRT Addict

Willow

Posted
  • Author
Posted

Yes HectorLooi you got that right wouldn't trade them for anything,oldhippy that's about the best photo i could get with the camera i have no micro on it hope you can manage to see it, i say a chip because it doesn't feel smooth when i run my nail along it more of a sharp step up

IMG_20200906_105010340_HDR.jpg

Link to comment
Share on other sites
oldhippy Distinguished Member

oldhippy

Posted
Posted

From that photo it doesn't look bad. If you have a smooth emery stick I would smooth it out. Try lowering the pallets by the means of the plate that screws onto the back plate. Make sure you oil the pallet faces, pivots and escape wheel teeth. If you have Windles clock oil that is the best you can buy, it doesn't cost a lot. 

Link to comment
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Restore formatting

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

×
 Share
Go to topic listing


  • Recently Browsing

    • No registered users viewing this page.

  • Topics

  • Posts

    • HorologyHead
      Intro

      By HorologyHead · Posted

      Hi to Blackminou29–am a collector/ caretaker—good luck to you following your repair course—with hindsight I wish I’d pursued a career in both watchmaker/ jeweler fields—good luck with whatever career passion you engage.   Thank you Watchweasol for posting the amazing TZIllustratedGlossary! Best wishes, Mike
    • JohnR725
      Seiko 6601 Tech Sheet?

      By JohnR725 · Posted

      yes I noticed the new site and I miss the old site. It's the unfortunate problem of the Internet here today gone tomorrow sometimes some of the stuff gets backed up and sometimes well it does not then the problem with the early Seiko's were there were not necessarily designed for distribution across the planet and as such there is no customer support for them. So trying to find early stuff like technical information or sometimes even parts list for older Seiko is is problematic. But I did find you a you tube video. A quick look he seems to take a heck of a lot of time to actually get to the service single I did not watch all that but it does look like he did disassemble or started to say there's a tiny bit here  
    • HorologyHead
      An intro…

      By HorologyHead · Posted

      RichardHarris123: Hello and welcome from Leeds, England.  I have family all over Australia, went as £10 poms Thanks Richard. Hope you’re able to visit your family here and that they’ve all done well 🙂 My relatives arrived from England in the 1790s transported on the ‘Second & Third Fleets’—a story of timber sailing ships, of convicts and doing well in this huge Country of Australia. When I visited the UK in the 1980s, I was too young to comprehend the depth and breadth of its history…  Best wishes, Mike William Chapman, my 4th great Grandad’s charges, at age 23 read at the Old Bailey; sentenced to 7 years of transportation to Sydney.
    • Endeavor
      New balance staff not riveting to balance

      By Endeavor · Posted

      The whole process and the progress are closely observed, it's hand-driven and very controlled. I can't see the "danger", unless you are watching the TV while doing it. As you could have read, and in this quote "wheel" is the balance-wheel.
    • Mercurial
      AS2063 - hand setting

      By Mercurial · Posted

      Have you got the pallet fork installed in the movement when you see the train move when using the setting works? As nevenbekriev said, without the pallet fork to lock the train, the behaviour you are describing is normal. If this is happening with the pallet fork installed, you have a problem in the gear train, it should be immobile when the pallet fork is locking the escape wheel.  The fit of the circlip above the pinions on that wheel is crooked in your pictures, it should sit flat up against the upper pinion as in Marc’s picture.  Hope that helps, Mark
×
×
  • Create New...