Jump to content

Roamer mst 372 not running


Recommended Posts

Hello again, 

Beginner here, so this might be something simple. I've got this old roamer, seems very cool. Have had it apart, all seemed ok. Gear train was moving freely, mainspring seems to work, balance looks ok, but it's still not running. 

Anyone have any tips on these movements, anything I should look out for? The balance seems very close to the lower plate, don't know if that might be a problem - 60/70 years old, maybe it's had a few knocks in its life. 

John 

20200823_132823.jpg

received_248288276197829.jpeg

Link to comment
Share on other sites

I'm no expert by any means, so just throwing in some thoughts: 

Was the parts cleaned and lubricated prior to reassembly?

How did you check the mainspring?

Are you sure that you assembled everything in order?

Did you check the pivots?

Link to comment
Share on other sites

Dose oscillator swing when the movement is wiggled? 

Is impulse in beat ?

Dose it not run in all positions?

Can you feel any free play on the staff ( end shake)?

Turn the oscilator like 60 degrees, let go, dose oscilator do a swing and dose fork move? 

Balance looking close to mainplate either means pivot on mainplate side is short/ broken or the jewel housing is to be moved up.

Dose roller table sit on the fork? 

Did you remove both end stones to check the jewels, dose it show excess end shake?

 

 

 

Link to comment
Share on other sites

Excellent, thanks for the responses.

Hector, the pallet seemed fine. I've never removed balance jewels, so that's something to try. 

Nucejoe, those are good suggestions, though honestly with things like endshake i wouldn't be knowledgeable enough to recognise if it's right or not. 

I think I'll start again, disassemble and clean, and have a closer look at those points. 

John 

Link to comment
Share on other sites

It does seem like something is happening between the mainspring and the escapement, possibly between the mainspring and the gear train, as its not transmitting any power, or at least there's no movement. The gear train moves freely when the mainspring barrel is removed 

Link to comment
Share on other sites

Grab balance rim with you tweezers, check  axial freedom of the staff, if no end play, end stones could be pushing on pivots.  Loosen cock screw a turn or two to create some end play. 

Sounds like pivot shoulder rubs on the lower jewel housing, to test, see if it runs face up.

Grab a spoke of the center wheel with tweezers and turn the wheel.

Was it running before? are yòu sure balance is in beat. Do you know how to check for in beat.

Link to comment
Share on other sites

It wasn't running, i got it in a box of approx 50 movements and whole watches, some running, some not. This one wasn't, but it's all there and looks in reasonable condition, no visible damage etc. 

No idea how to check if it's in beat 

Link to comment
Share on other sites

Just now, Johndub said:

Ok, cool. I've got it disassembled again, cleaning it with naptha. Will fit the balance on its own and see how that looks. 

Is naptha safe to use on all parts? I feel i read somewhere that maybe not on the pallet? 

Naptha is good for all parts. You shouldn't use IPA on the pallet fork and balance assembly as it may damage the shellac. 

Link to comment
Share on other sites

Oh goodness, when the fork is out, if oscilator comes to rest with its impulse jewel in midpoint between the banking pins, impulse would then be in beat , in such case, staff and fork and escape pivits should fall on a straight line.

Link to comment
Share on other sites

No need to disassemble, if you suspect lube problem, drop a bit of naphta or lighter fluid on top of end stones( both side) it will penetrate to the jewels and temporarely softens gummed up oil, oscilator then picks up and run.

Link to comment
Share on other sites

Balance jewels definitely need to be cleaned.  A bit fiddly as you need to dismount the balance from the cock but no way around it. Don't be tempted to remove the balance jewel screws thru the hairspring... on that path lies disaster!.

Anilv

  • Thanks 1
Link to comment
Share on other sites

Anvil said it "No way around it"   remove, check, clean and lube end stones& jewels, that is standard proceedure. I have made a habbit of soaking the cock in coca cola or you can put penetrating oil on them two little screws and make sure to use the right and dressed screwdrivers, to reduce the risk of ordering from cousinsuk.:lol:

To test for llubrication issue, I just drop some lighter fluid on jewel assembly.

Link to comment
Share on other sites

Thanks for all the advice, it'll be very useful for other projects as I'm learning. Unfortunately i broke the top arbor of the escape wheel last night (as well as losing the setting spring lever screw). 

So the roamer is beyond my fixing abilities for now anyway. I do see that cousins have them, but at 20 pounds plus 10 shipping, so I'll be leaving it aside for now. Maybe a parts one will show up on ebay 

Link to comment
Share on other sites

35 minutes ago, HectorLooi said:

Does anyone else think this sentence sounds bad? Or should I disinfect my brain with Chlorox? :D

Well, seems there's a lot of questionable terminology in this hobby. 

Setting screw lever turned up this morning. Scoured the floor last night and no sign, then there it was on the table this morning. So that's a positive. 

 

  • Like 1
Link to comment
Share on other sites



  • Recently Browsing

    • No registered users viewing this page.
  • Topics

  • Posts

    • I've managed to adjust it. I'm going to try and explain it as well as I can with my limited horology knowledge but I hope it helps someone in the future. There is a cam to the right of the front plate as shown in the picture. As the clock ticks along, the pin indicated in the gear comes around and slots into one of the silencer cam gaps, turning the cam. The pin completes a full rotation in 2 hours. To adjust the cam to start at the right time set the clock to just before 7. I did 6:45. Then I turned the silencer cam anticlockwise, which spins freely, until it pushed the silencer lever up and was placed just before the drop. Just before the 7AM indicated in the picture. All I then had to do was progress the hands to 7-7:15which made the pin slot into the silencer cam gap and turn the cam so the lever comes down again, unsilencing the clock. That was it. If anyone comes across this issue again I'd be happy to assist. Thanks again to everyone that helped.
    • Now I'm completely confused, it would appear that the epilame  is oleophobic  as @Marc states: This oleophobic  behavior can be seen as beading of the droplet (as above) which stops the oil spreading which is supported by what we observe on treated/untreated cap stones (for example), but as @VWatchie states this should make the drops more mobile, and not less mobile which is the opposite of what we want. In fact this beading and high mobility are desirable properties in things like smart phone covers, see below.  I am fairly sure that epilame doesn't make the droplets more mobile, so maybe its a strange coating with dual properties that are both oleophobic and cohesive/adhesive resulting in low mobility?? This may explain the high price??  
    • The description there is exactly how it's done, and it's very well written!
    • Would it be correct to say that the stronger the mainspring, the thicker the oil should be? So for a fusee mainspring, should a thick grease be used?
    • I started on pocket watches as they are easier to work on than wristwatches. Many had gold cases, which is why there are so many movements for sale. I was always on the look out for cases, for as Nickelsilver says,  a 16s movement will fit any 16s case* (with tweaks to the stem). I also started hand winding mainsprings, before I had winders. It can be done without damage, but it's quite hard on the fingers.  But you can make homemade winders, see here      * some movements, eg "railroad grade", have a setting lever on the edge of the  dial at about the 1 -2 o'clock, so need a special case.
×
×
  • Create New...