Jump to content

mainspring replacement - first time advice needed

cduke

By cduke
in Watch Repairs Help & Advice

 Share

Recommended Posts

cduke WRT Addict

cduke

Posted
Posted

Hello All,

I am going to attempt a mainspring replacement for the first time and I will try to do this by hand as I do not own the set of winding tools.  I know it would be infinitely easier but they are not inexpensive and I am new to all of this.  Question is...the mainspring comes coiled in a disc typically.  Can it be transferred to the barrel without unwinding it and rewinding it into the barrel?  I apologize if this question seems lazy but I am trying to do this without too many chances to become unwound.

Link to comment
Share on other sites
MyRetroWatches Member

MyRetroWatches

Posted
Posted

I have a video n my channel for hand winding a spring.  its frowned at by many... but it works. as for new ones , no need to unwind. Just put over the barrel so it fits and use something flat to push it in.  At least thats how I have done it anyway. 

Alignment is everything. 

  • Like 2
  • Thanks 1
Link to comment
Share on other sites
jdm Distinguished Member

jdm

Posted
Posted
4 minutes ago, MyRetroWatches said:

 no need to unwind. Just put over the barrel so it fits and use something flat to push it in.

This is how it's done and it has been mentioned here so many times (always good to search before asking), BUT...

If it's manual wind it's good to check first that the tongue engages the cut on the barrel. Before placing the lid turn the arbout with pin vices. Otherwise, depending on the mov.t you may find that it doesn't (it happened to me), and you will have to go back, remove and rewind to correct the problem. Truth is, having a winder is always a good idea.

Link to comment
Share on other sites
MyRetroWatches Member

MyRetroWatches

Posted
Posted
This is how it's done and it has been mentioned here so many times (always good to search before asking), BUT...
If it's manual wind it's good to check first that the tongue engages the cut on the barrel. Before placing the lid turn the arbout with pin vices. Otherwise, depending on the mov.t you may find that it doesn't (it happened to me), and you will have to go back, remove and rewind to correct the problem. Truth is, having a winder is always a good idea.

I did not ask the question. Was answering it.


Sent from my iPhone using Tapatalk
Link to comment
Share on other sites
jdm Distinguished Member

jdm

Posted
Posted
Just now, MyRetroWatches said:

I did not ask the question. Was answering it.

And I did not criticize your answer. Starting from it, have added an additional tip, if you allow me.

Link to comment
Share on other sites
jdm Distinguished Member

jdm

Posted
Posted
Just now, MyRetroWatches said:

No problem. I am on Tapatalk so maybe it’s displaying wrong. Apologies

I recommend that you don't use it here. It causes many troubles and our Host Mark is about to remove support for it. The forum software is well engineered to allow full, unhindered support to all features from mobile devices.

 

 

  • Like 1
Link to comment
Share on other sites
cduke WRT Addict

cduke

Posted
  • Author
Posted
20 minutes ago, MyRetroWatches said:

I have a video n my channel for hand winding a spring.  its frowned at by many... but it works. as for new ones , no need to unwind. Just put over the barrel so it fits and use something flat to push it in.  At least thats how I have done it anyway. 

Alignment is everything. 

I've viewed this video ( I think its yours) and it is a big help in understanding how it can be done.  You had two old part barrels and you unwound and rewound by hand. Is that the one?  I have never seen anyone simply transfer the spring directly from the disc which seems logical.

Link to comment
Share on other sites
Nucejoe Distinguished Member

Nucejoe

Posted
Posted

Apart from other issues, since the barrel is greased before MS is pushed in,  hand winding spring in becomes a greasy mess. Just push on the coil to insert it in, to avoid breaking the spindle,  it should be slid in along the line of cut on barrel wall.

  • Thanks 1
Link to comment
Share on other sites
MaverickWaz Member

MaverickWaz

Posted
Posted
I've viewed this video ( I think its yours) and it is a big help in understanding how it can be done.  You had two old part barrels and you unwound and rewound by hand. Is that the one?  I have never seen anyone simply transfer the spring directly from the disc which seems logical.

Hi Duke,

 

You're correct in that you can simply transfer the mainspring from the ring into the barrel. Just make sure it's seated correctly and is orientated the correct way. I understand why you asked the question as it is a little daunting the first time you do it but if done slowly with a flat implement there's very little that can go wrong.

 

Some people probably do it different but I've always used the other end of a pair of tweezers as they're solid and flat.

 

Good luck! By the way I haven't sprung for a set of mainspring winders yet and have always opted to simply purchase a new mainspring and insert it using the above method.

 

To help illustrate what to check for before putting it home I added a very crude image below. Just make sure it's all the way in up to the disk all around.

 

 

a29e6af399a137c3d7cd6f5846f9813b.jpg

 

 

Sent from my SM-T510 using Tapatalk

 

 

 

  • Thanks 1
Link to comment
Share on other sites
pubudeux Watch Enthusiast

pubudeux

Posted
Posted (edited)
8 hours ago, MyRetroWatches said:

I have a video n my channel for hand winding a spring.  its frowned at by many... but it works. as for new ones , no need to unwind. Just put over the barrel so it fits and use something flat to push it in.  At least thats how I have done it anyway. 

Alignment is everything. 

I learned how to do this from your video, thanks for that it was great.

The bit about the pin vise is great, and having one really helped me in the learning process, being able to test whether the arbor was properly hooked up to the mainspring.

 

I got a Starett pin vise for .8-1.6mm diameter, which is perfect for this purpose.

Edited by pubudeux
  • Thanks 1
Link to comment
Share on other sites
 Share
Go to topic listing


  • Recently Browsing

    • No registered users viewing this page.

  • Topics

  • Posts

    • JohnR725
      Seiko 6601 Tech Sheet?

      By JohnR725 · Posted

      yes I noticed the new site and I miss the old site. It's the unfortunate problem of the Internet here today gone tomorrow sometimes some of the stuff gets backed up and sometimes well it does not then the problem with the early Seiko's were there were not necessarily designed for distribution across the planet and as such there is no customer support for them. So trying to find early stuff like technical information or sometimes even parts list for older Seiko is is problematic. But I did find you a you tube video. A quick look he seems to take a heck of a lot of time to actually get to the service single I did not watch all that but it does look like he did disassemble or started to say there's a tiny bit here  
    • HorologyHead
      An intro…

      By HorologyHead · Posted

      RichardHarris123: Hello and welcome from Leeds, England.  I have family all over Australia, went as £10 poms Thanks Richard. Hope you’re able to visit your family here and that they’ve all done well 🙂 My relatives arrived from England in the 1790s transported on the ‘Second & Third Fleets’—a story of timber sailing ships, of convicts and doing well in this huge Country of Australia. When I visited the UK in the 1980s, I was too young to comprehend the depth and breadth of its history…  Best wishes, Mike William Chapman, my 4th great Grandad’s charges, at age 23 read at the Old Bailey; sentenced to 7 years of transportation to Sydney.
    • Endeavor
      New balance staff not riveting to balance

      By Endeavor · Posted

      The whole process and the progress are closely observed, it's hand-driven and very controlled. I can't see the "danger", unless you are watching the TV while doing it. As you could have read, and in this quote "wheel" is the balance-wheel.
    • Mercurial
      AS2063 - hand setting

      By Mercurial · Posted

      Have you got the pallet fork installed in the movement when you see the train move when using the setting works? As nevenbekriev said, without the pallet fork to lock the train, the behaviour you are describing is normal. If this is happening with the pallet fork installed, you have a problem in the gear train, it should be immobile when the pallet fork is locking the escape wheel.  The fit of the circlip above the pinions on that wheel is crooked in your pictures, it should sit flat up against the upper pinion as in Marc’s picture.  Hope that helps, Mark
    • Khan
      Stem broken - can it be rescued?

      By Khan · Posted

      Hi I got a Jaeger LeCoultre K911 movement, where one of the stems was broken. Part no. Should be 401.  Im based in Europe and tried Cousins but its discontinued. They except to get stem in stock for cal. K916 but will that work? Or Is there a way out to join the ends?
×
×
  • Create New...