Jump to content

Roller too tight - how do I reduce the roller seat on the balance staff

mikepilk
 Share

Recommended Posts

mikepilk Distinguished Member

mikepilk

Posted
Posted

I have a new balance staff to fit an Omega 26.5. It fits OK apart from the roller being too tight.

Is there any way I can reduce the roller seat diameter, as  I'd rather do this than broach the roller?

I don't have a lathe, but do have a Jacot tool - but can't see a safe way to do it.

Any ideas ?

 

0001.png

Link to comment
Share on other sites
nickelsilver Distinguished Member

nickelsilver

Posted
Posted

When I was in school I worked evenings in a trade shop (servicing multiple stores) that was for all intents and purposes a "hack" shop. No lathe, but I was required to wire brush the back of every dial (?!)... and so had a Dremel hanging at the bench. I quickly got all the restaffing work too, and found I could chuck the staff in the Dremel and stone down such diameters pretty effectively. It killed me as I'm a lover of lathes and turning, but the watches went out and ran well.

My boss would just broach the roller. Usually a new one, as he'd crush the original trying to force it on. Nice guy though.

  • Like 1
  • Thanks 1
Link to comment
Share on other sites
mikepilk Distinguished Member

mikepilk

Posted
  • Author
Posted
26 minutes ago, nickelsilver said:

When I was in school I worked evenings in a trade shop (servicing multiple stores) that was for all intents and purposes a "hack" shop. No lathe, but I was required to wire brush the back of every dial (?!)... and so had a Dremel hanging at the bench. I quickly got all the restaffing work too, and found I could chuck the staff in the Dremel and stone down such diameters pretty effectively. It killed me as I'm a lover of lathes and turning, but the watches went out and ran well.

My boss would just broach the roller. Usually a new one, as he'd crush the original trying to force it on. Nice guy though.

Good idea - I have a Dremel clone.

Link to comment
Share on other sites
 Share
Go to topic listing


  • Recently Browsing

    • No registered users viewing this page.

  • Topics

  • Posts

    • Neverenoughwatches
      New balance staff not riveting to balance

      By Neverenoughwatches · Posted

      You often see the term used on old watch part boxes.  Staffs for bracelet watches, timing washers for bracelet wstches etc.
    • Chief
      Intro

      By Chief · Posted

      The Boro has changed quite a lot over the last 20 years, and not for the better. I actually moved out of the town 15 years ago to a small village not far away. Thanks for the pdf! Looks a great read. I'll get it printed today and put it on my work bench!
    • Endeavor
      New balance staff not riveting to balance

      By Endeavor · Posted

      Not having all the fancy equipment, this is a way I came up with. I never said it was the best, the most ideal or the safest way. Working on balances is always a delicate task whereby full concentration & common sense should prevail. I was well aware of the "dangers" / short comings involved, hence my "warnings", as quoted above. The balance wheel of the Omega was nice true, flat and one could clearly see how much gap there was left before the grinding wheel would touch the balance wheel. I stopped when the generously applied diamond paste started to touch the rim of the balance wheel, which turned out to be with a seat thickness left of 0.1mm. Tapping the remainder of the staff out went easy and flawless. My idea of penning this article was to show/share a way which, in my case, perfectly succeeded. If deemed to risky, or if the balance wheel is not true or has a wobble, other methods have to be followed.
    • Neverenoughwatches
      Seiko 6601 Tech Sheet?

      By Neverenoughwatches · Posted

      I loved his explanation of a teardown 😅 Ex military Richard Perrett, pretty knowledgeable guy.
    • praezis
      New balance staff not riveting to balance

      By praezis · Posted

      I also see a bit of danger for the wheel, at least you have to keep away from it and may get a too thick rest ring. My rest rings are about 0.05 mm. Better way would be a grinding wheel touching the staff with its circumference. Frank
×
×
  • Create New...