Jump to content

Recommended Posts

Posted (edited)

I think we need to put things into perspective, we can't treat the watch like its some kind of death machine when we are working on it and then as something benign after that and wear it day-to-day on our wrist, a good example of cognitive dissonance. I know that the body of the watch will block the alpha radiation which is the main concern, but the radiation detectors don't pick up alpha, so it is definitely throwing off other types of radiation too, otherwise our detectors would be useless. I typically get the hands off as soon as I can and dunk them in a benzine jar with acetone, for PPE I use finger cots. I then dispose of the cots and (contaminated) acetone, I give the watch body (including the dial) a few puffs of air outside on my balcony to remove any free radium dust. Hence, the only remaining radium will be on the numbering on the dial, but this is usually a lot less free to flake or become something you can pick up on your fingers or breath in as it is glued in place and it can only become free if you start messing with it.

After the above I treat the watch like any other.

The extremes some people go to reminds me of a conversation I had in the late 90's or early 2000's when a friend of mine said he would never use a cell phone as it gave you brain cancer, the irony was that he was smoking while he was telling me this. So, it's all about quantifying risk, get a radiation detector and take reasonable precautions to massively reduce the already minuscule risk without overdoing it. I don't think there are any data to support a conclusion that watchmakers are at a statistically significant increased risk of radiation related ailments than those that are not exposed to the risk of radium, but, of course, absence of evidence is not evidence of absence, thus my reasonable precautions above.

Edited by Waggy
Posted
  On 10/18/2023 at 12:28 AM, LittleWatchShop said:

My dad serviced many thousands of watches from 1947 to 1990. He never worried about radium. He died at age 93. Was not caused by radium.

Expand  

That argument is used by smokers :- "I knew someone who smoked and lived to 100"

People have fallen out of aircraft without a parachute and survived.  If jumping out of an aircraft, I would want to be wearing a parachute.

  • Like 1
Posted

I think we are arguing the same point from different directions, I suppose what I was trying to do (badly) was introduce the concept of ALARP (as low as reasonably practicable) which involves lowering a risk as much as possible without increasing unreasonably the trouble, time and money needed to control it. In your example I agree with you that a parachute and a reserve would be ALARP, but adding 3rd or 4th parachute 'just in case' would not be ALARP.

The reason I hesitated using the acronym is that it ALARP is frequently perverted into a justification for cheeping out on safety, or as it is commonly known: as low as reasonably PRICED. But in its true form I believe even modest precautions with radium would be ALARP.

 

 

Posted (edited)
  On 10/18/2023 at 9:40 AM, mikepilk said:

That argument is used by smokers :- "I knew someone who smoked and lived to 100"

People have fallen out of aircraft without a parachute and survived.  If jumping out of an aircraft, I would want to be wearing a parachute.

Expand  

That was my anecdotal evidence. Give me yours. Evidence of one watchmaker who died from radium induced bone cancer. This radium fear has been overly hyped.

  On 10/18/2023 at 10:26 AM, Waggy said:

ALARP

Expand  

I like acronyms.

To minimize Risk/Reward, we can either reduce risk, or increase reward. For horological radium (let's call it HR), there is some unknown risk that cannot be quantified nor agreed upon. But whatever it is, give it a value and fix it.  Then ask yourself about the reward. Except in rare cases, probably not much.

Back to ALARP...reminds me of the Alar scare.

Life is full of risks and rewards. You place your bet and spins the wheel!

Edited by LittleWatchShop
Posted (edited)
  On 10/18/2023 at 10:30 AM, LittleWatchShop said:

That was my anecdotal evidence. Give me yours.

Expand  

I haven't searched for any, but "anecdotal evidence" with a sample of one is not evidence.

To back up my point, I can give you real evidence of people who fell out of aircraft and survived, or smoked and lived to old age. I'm not saying there is a problem, but "anecdotal evidence" does not prove there isn't.

Nullius in verba

(Just found this, interesting. I only have one radium dialed watch, which I keep in a ziplock bag. I don't know if that contains the radon)

https://www.hodinkee.com/articles/new-report-shows-radium-dials-might-pose-serious-danger

(BTW I'm with you in thinking that the danger is generally exaggerated)

Edited by mikepilk
Posted

Radium is extremely dangerous and all watches tools and parts even your house that have come in contact with it should be sent to me immediately.

Posted

I spit in the eye of danger @LittleWatchShop  🤣 

I was going to post pics of radium toothpaste, water, and suppositories (😯), but it's a bit off topic.

But I do need to get some of this hand cleaner, it sounds great : "Takes off everything but the skin"  
. . . but given time.

 

image.png.3f786ece09fe7447f4fa8d6019c810d9.png

 

 

 

😯  

  • Like 1
Posted

That was an interesting study.  I never thought I'd see the word "gonadol" in print, but there it is: "Robinson (1968) estimated the average gonadol dose-equivalent rate was 3 339 mrem/y (0.03 mSv/y) for each of the 10 million people in the USA who wore such watches . . . ." 

 

I guess the upshot of the study is to take precautions not only with the radium but also with the radon gas.  

  • Like 1
Posted
  On 10/18/2023 at 7:43 PM, mikepilk said:

Found with a bit of Googling (I think this is the right one, I haven't read it yet)

Expand  

Interesting read. Although I have previously mentioned contamination in Scotland caused by Timex (Dundee)  and Westclox (Dumbarton) and the scrap dial disposal at the site in Fife, I had forgotten about the contamination in Wishaw at Gowkthrapple, next to the former site of a primary school, caused by Smiths Industries luminising plant (watch and instrument dials).

Incidentally a lot of this radioactive junk was "disposed of" (i.e. thrown off the back of a ship) in the Beauforts Dyke area of the Atlantic between Scotland and Ireland, along with masses of unexploded WW2 and later ordnance, which includes white phosphorous bombs. These wash up from time to time on the coasts around this area. Presumably all sorts of other contaminants are down there too, as the oceanic trench was treated as a magic portal into which anything could be thrown, in order to make it simply vanish from public concern.

Maybe it will make for self heating fish with real fish fingers. 😋

Posted
  Quote

"The HSE (2002) highlighted controls on timepieces containing radioactive substances for those in the retail and antique trade, noting that they were no longer free to dispose of damaged luminised clocks and watches with general refuse (96/29/EURATOM)."

Expand  

I take it from that, burying them in the garden is now the preferred method.

It seems that the advice, post 2002 is now even more ambiguous. A domestic user, can dispose of in the domestic waste, but someone in the "retail and antique trade" cannot, so you can't throw it in the bin at work, but you can take it home and throw it in the bin. Sounds like the typical joined up "gubmint" thinking we have all come to know and love in this country.

Posted
  On 10/18/2023 at 7:43 PM, mikepilk said:

Found with a bit of Googling (I think this is the right one, I haven't read it yet)

Crockett_Robin_E_2012_Radium_dial_watches_a_potentially_hazardous_legacy.docx.pdf 1.25 MB · 7 downloads

Expand  

Very interesting reading, especially about the radon danger. This is important reading for those who have collections of radium dialled watches.

Is there a way it can be posted at a higher level to make those people aware?

Posted
  On 10/19/2023 at 8:45 AM, Waggy said:

Here is the paper in its published format:

Expand  

That's much easier to read, thanks.

From what I've found about radon gas. It's easily contained in an airtight container, so my ziplock bags work OK. But, it decays to daughter products which contaminate the inside of the container. So open it outside.

  • 7 months later...
Posted

Radium hands. treat with respect
Radium dial numbers, usually under the varnish coat and also not nearly as active when tested.
Basically don't eat it and wash hands after dealing with it
Ladies who died from radiation poisoning from watch industry were ingesting large amounts daily for years

Posted
  On 6/3/2024 at 8:42 AM, stylo9 said:

Radium hands. treat with respect
Radium dial numbers, usually under the varnish coat and also not nearly as active when tested.

Expand  

Depends on how much radium was used on the numbers

image.png.ccd13f9c8bf4ddeee9b953c7d50596d2.png

  • Like 3
Posted
  On 10/19/2023 at 8:45 AM, Waggy said:

Here is the paper in its published format:

gillmore2012.pdf 989.44 kB · 8 downloads

Google scholar reports it has been cited 15 times, so reasonable testament that it is a good paper 

Expand  

Wow @RichardHarris123, I didn't know you were a famous scientist! You are one of the authors, right?

 

  On 6/3/2024 at 9:32 AM, swiss2k said:

 

I found this presentation interesting.

Expand  

I watched this a few years ago.

What I found interesting is the title of her presentation "how I stopped worrying about radium dials"...... BUT then she carries her watches in a lead-line bag!?!? Sounds like a contradiction to me.

 

Personally (!!!!), I don't want to work on radium dials/hands. Which is a shame, because I love watches from the 1930s to 50s. Even when working on tritium dials, I wear a mask, wear cots (as always..), open the window, try to remove any loose lume with Rodico and then dispose of it, and wash my hands thoroughly.

I assume that this level of precaution may be excessive (for Tritium), but I would think that it's the minimum when working on Radium. Especially a mask, I'd say, is essential to avoid inhaling any particles. I understand that's the main risk for Radium and its alpha radiation, which is harmless in a closed watch case with its crystal, but dangerous inside the body.

I keep my watches, including one with a lot (!) of Radium on the dial and hands in a normal watch box -- I guess I should rather keep it in a well-ventilated area due to its Radon gas emissions. 

 

My approach is based on some researching on the topic + an innate fear of radioactivity (maybe based on my mother's stories of Chernobyl fallout/rain when I was a small child).

  • Like 1
Posted
  On 6/4/2024 at 12:02 PM, Knebo said:

What I found interesting is the title of her presentation "how I stopped worrying about radium dials"...... BUT then she carries her watches in a lead-line bag!?!? Sounds like a contradiction to me.

Expand  

Same here. I watched it several years ago and I concluded that she concluded nothing.

  • Like 2

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Restore formatting

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.


  • Recently Browsing

    • No registered users viewing this page.
  • Topics

  • Posts

    • I was thinking it might be nice to see a picture up above or the picture I'm going to paste down below from up above with the escape wheel just setting their. Then it almost looks like the lower jewel is out quite a ways? But maybe it's an optical illusion with the shellac yes the assortment set over time have become something other than what they once were. Like it work with a assortment of Waltham jewels for burnishing in and the last time I tried to find one I discovered there all randomly assorted. Then of course often times the assortments had a tiny quantity of things and the entire container got re-tasked for other things and down the road somebody sells it totally clueless of what they're selling. But in the case of roller jewel's especially after the longer ones of pocket watch size for a single roller then randomly and bottles is definitely good. If you really careful you may bill to place the roller jewel on a flat surface and use calipers although a bench micrometer really is preferred.
    • Have you search for a new winding crown using Tissot case id? You can also find a replacement crown by size / type of the crown you currently have: https://www.cousinsuk.com/category/tissot-crowns-by-size They are dirt cheap.
    • yes the pocketwatch database shows quite a spread in those serial numbers. With the watches typically made in batches and even in a batch from the beginning to the end there be some variations. Then you have approximately a 10 year difference between the two yes some of the stuff will probably not fit especially escapement components as there usually adjusted at the time of manufacturing and of course manufacturing tolerances were improving with time. https://pocketwatchdatabase.com/search/result/elgin/36764469 Grade:    315    Model:    3     Class:    114   Estimated Production Year:    1937  Run Quantity:    4,000     Grade/Model Run:    310 of 329 https://pocketwatchdatabase.com/search/result/elgin/19110954 Grade:    315     Model:    3     Class:    114    Estimated Production Year:    1917   Run Quantity:    2,000     Grade/Model Run:    127 of 329  
    • Hope you let the mainspring completely unwind before removing the bridge? Use not only a screwdriver, but a pair of good tweezers with curved ends. This will allow to move various sides of the bridge straight up while keeping it in parallel with the main plate. If you use a screwdriver only and top pivot is stuck, then a bridge is being lifted under angle and then you hear that "horrible click". Usually it takes only one instance to learn such lesson in life 😅
    • Regarding the spring winders, I made my own and used copper pipe reducers as the tubes to retain the spring. You will need to cut out a section for the end of the spring to protrude but if you watch one of the many videos on this subject that will make sense. You can find a selection of sizes on Ebay for very little cost. I'll attach a pic showing one of mine.  Good luck!
×
×
  • Create New...