Jump to content

We have another clock competition.


oldhippy

Recommended Posts

The backcock seems to have been altered in some way it has a different coloured brass dove tailed into the top, so has it been converted to a suspension pendulum rather than having the pendulum directley fitted to the staff. The movement has been propped forward at an angle is this an attempt to stop the verge from moving and disengaging from the crown wheel due to wear ?

Also why have the fusee arbours got holes drilled in the middle ?

I also note that this is not the first time the seller has tried to sell this clock it was originally listed in September but was complete with movement brackets which have since been removed.

https://www.ebay.co.uk/itm/282023666266

I should have said barrel arbours not fusee arbours that have holes in

Edited by wls1971
Link to comment
Share on other sites

Most of what I spotted and a lot I didn't spot has already been mentioned, but clearly its a marriage of the movement to the dial and case, which explains the horrible hacking up of the baseboard to provide the clearance for the pendulum

I also cant decide if the hour and minute hand are a set, or mismatched.

I would of thought this dial should be silvered too, but it looks to be just brass.

Certainly not worth the asking price

Link to comment
Share on other sites

What we have is a verge-striking movement with a completely different replacement pendulum. You do not have a suspension spring with an original verge escapement. Many original verge escapements will only have one pivot which goes into the inside plate, the other end will be a V shape that sits in the back cock. That cock has be altered; the brass is a different colour, as so rightly pointed out. It would have had the V end, it has been changed to a pivot end, that is why a part has been added and the whole pitch to the castle wheel has changed. You have to be extremely careful when moving such a clock. You must tilt it into yourself to prevent the V shape from lifting. Some have a cover to prevent such a thing happening, it is very important to check first. I suspect that the movement and dial is a marriage to that case. There is nothing to hold that movement in place to that case. The reason it is tilted, if you look carefully that piece of odd wood isn’t even the width of the movement. The hands are correct but the hour looks a little heavy. The hook is still there to attach the original verge pendulum. The pendulum is a bodge up from top to bottom. Have you noticed the poor re-bushing for the fusee cone on the strike side? It stands out like a sore thumb.  

I think I have covered everything.

 

Everyone who has remarked about the clock has got some points right. :Bravo:

 

Link to comment
Share on other sites

  • 1 month later...

I am a new member, therefore did not see this when listed, however can I add three things to the list. The right side screw in the backcock is a replacement and the hammer looks to be set halfway through the strike and the foot looking at the case from the back is also a replacement and a poor one at that.

Link to comment
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Restore formatting

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.



  • Recently Browsing

    • No registered users viewing this page.
  • Topics

  • Posts

    • I also see a bit of danger for the wheel, at least you have to keep away from it and may get a too thick rest ring. My rest rings are about 0.05 mm. Better way would be a grinding wheel touching the staff with its circumference. Frank
    • Not easy to find this one everywhere,  so it depends where you are located. Joining it back together might be possible, i have silver soldered mild steel before even with traditional plumbers lead and its a pretty strong joint, but bere in mind this is only 1mm diameter.  The join would need to be very accurate,  it not something i have heard of anyone trying before. The part no 401 is the swiss code number and relates to watch winding stems in general
    • Thanks everyone for your helpful replies. I think between us we’ve worked out what’s going on. Next job is to have a proper look at this great wheel assembly, see if I can remove the clip and the friction fit pinion, give the bits a good clean, then put it back together with a bit of blue grease. I’ll also get the pallet fork under the microscope to see if it’s ok or been damaged. 
    • The cannon pinion (be it conventional style or what you see in this movement) should slip on its arbour so the hands can be set independently without affecting the gear train.  If there is too much friction between the cannon pinion and the second wheel, turning the hands to set them backwards can sometimes force the escape wheel teeth to overrun the pallet stones, creating the behaviour you describe. The train is running in reverse when this happens.  This can often chip the pallet stones. I’d say at least half of the watches I’ve inspected with very tight cannon pinions had chipped pallet stones. Hopefully this isn’t the case with your watch.  I’m not familiar with this movement but you need to get the friction in the cannon pinion adjusted correctly.  Hope this helps, Mark
    • Pallet fork was in. I’d had the movement running ok, and only removed the balance to flip it over and install the keyless works and date mechanism. The pallet fork wasn’t locking the gear train when hand setting - it was oscillating as the escape wheel rotated. This may have been in one direction only - can’t remember. 
×
×
  • Create New...