bsoderling Posted May 29, 2018 Share Posted May 29, 2018 Hi, I came across an old tank style watch where the movement must be front loaded as there’s no case back to remove, the movement sits deep in the hollowed casing. I have limited experience from split stems. I have encountered one where the stem ended in a ”hook” and I could slide out the movement by finding the correct turning angle for the crown. This one doesn’t seem to work that way... I have attached a photo showing where the stem goes into the casing and besides the stem being of wider diameter than usual, there’s also what appears like slots on opposite sides that I suppose may indicate where the stem can separate? I have tried to pull the crown hard but nothing happens and I’m afraid something may break. I would appreciate some advice here and if it’s just brute force that counts... /Bsoderling Sent from my iPad using Tapatalk Link to comment Share on other sites More sharing options...
Chopin Posted May 29, 2018 Share Posted May 29, 2018 I can't tell from the photo what we're dealing with here but some stems and crowns are male/female type. Link to comment Share on other sites More sharing options...
bsoderling Posted May 29, 2018 Author Share Posted May 29, 2018 Hi Chopin, that was for sure speedy response :-),And right you are, I tried a pair of wire cutters with steep edges under the crown and off it came...Photo is attached. Pretty nice movement, don’t you think? And actually ticking with some determination. Thanks!Sent from my iPad using Tapatalk Link to comment Share on other sites More sharing options...
oldhippy Posted May 29, 2018 Share Posted May 29, 2018 In the first photo, the setting lever spring is broken. Just wondering if the broken bit is wedged and is preventing the two piece stem from disengaging. Link to comment Share on other sites More sharing options...
bsoderling Posted May 29, 2018 Author Share Posted May 29, 2018 Thanks oldhippy, good thought but not the case as you can in the recent posting. On setting lever springs, I find these to be very often gone on the old-timers I through myself at. Luckily the watch isn’t really depending on this ”feature” and I most often accept it for a fact as chasing up the correct part can be both endless and, if I find the part, expensiveAgain thanks for all input!Sent from my iPad using Tapatalk Link to comment Share on other sites More sharing options...
Chopin Posted May 29, 2018 Share Posted May 29, 2018 (edited) These crowns do indeed come out with difficulty but then again it's better than having a crown slip off while simply adjusting the time. Indeed that is a lovely little movement and it sure looks to be of, more or less, high quality. What is it ? You can use pliers or really thick tweezers but you can try and put something between the metal and the teeth of the tool that you use to protect the metal. Edited May 29, 2018 by Chopin Link to comment Share on other sites More sharing options...
bsoderling Posted May 29, 2018 Author Share Posted May 29, 2018 The dial says ”Mowy” but there’s no id visible anywhere on the movement so I presume it’s a ”generic” of some kind.What intrigued me was the rather elaborate casing design with all its bits an pieces... phota attached.Sent from my iPad using Tapatalk 1 Link to comment Share on other sites More sharing options...
vinn3 Posted May 29, 2018 Share Posted May 29, 2018 5 hours ago, Chopin said: I can't tell from the photo what we're dealing with here but some stems and crowns are male/female type. the 2 part stem as pictured above is the standard for the front loader vintage wrist watch. use an old pair of tweezers to apply an even pressure when prying it off. new watches may be different. vin Link to comment Share on other sites More sharing options...
rogart63 Posted May 30, 2018 Share Posted May 30, 2018 18 hours ago, bsoderling said: Hi Chopin, that was for sure speedy response :-), And right you are, I tried a pair of wire cutters with steep edges under the crown and off it came... Photo is attached. Pretty nice movement, don’t you think? And actually ticking with some determination. Thanks! Sent from my iPad using Tapatalk Whats the size of that movement? It's either a FHF or a ETA i think. Link to comment Share on other sites More sharing options...
vinn3 Posted May 30, 2018 Share Posted May 30, 2018 19 hours ago, bsoderling said: The dial says ”Mowy” but there’s no id visible anywhere on the movement so I presume it’s a ”generic” of some kind. What intrigued me was the rather elaborate casing design with all its bits an pieces... phota attached. Sent from my iPad using Tapatalk the case appears to be a Wyler. vin Link to comment Share on other sites More sharing options...
rogart63 Posted May 30, 2018 Share Posted May 30, 2018 Have two "Wyler" movements here. wonder if any of the can be the same. Has no markings on them . Only that one of them has a Wyler dial. Link to comment Share on other sites More sharing options...
bsoderling Posted May 30, 2018 Author Share Posted May 30, 2018 Hi and thanks for all the interesting info.Wyler is an unknown for me. Will google a bit to catch up.The movement baseplate measures 17,5 x 26 mm. I have attached a photo of the dial. Have seen better but also a lot worse :-)Sent from my iPad using Tapatalk Link to comment Share on other sites More sharing options...
bsoderling Posted May 30, 2018 Author Share Posted May 30, 2018 Indeed....found a Wyler thread on watchuseek that talks about a close to identical watch. The movement is mentioned as MST 312 in the thread. Any info on that is appreciated.The one I got has some kind of shock proof add-on though, so maybe it’s somewhat younger?I presume the ”wy” in ”Mowy” is there to indicate a sub-brand to Wyler. There seems to have been variations on that theme at the time. I´ll make sure to post the final result of my efforts when done with the service and clean-up.Sent from my iPad using Tapatalk Link to comment Share on other sites More sharing options...
rogart63 Posted May 30, 2018 Share Posted May 30, 2018 Movement is probably a FEF 130 -149 . Or it is a FEF but what number? http://www.ranfft.de/cgi-bin/bidfun-db.cgi?10&ranfft&2&2uswk&FEF_139 Link to comment Share on other sites More sharing options...
Recommended Posts