Jump to content

Stem extension help

Chopin

By Chopin
in Watch Repairs Help & Advice

 Share

Recommended Posts

Chopin Super WRT Addict

Chopin

Posted
Posted (edited)

I have to use a stem extension on a Seiko Diver's with a screw down crown and I have some questions as I've never done this before.

First of all, how do you tighten the stem to the stem extension ? I know that I'll probably have to use a bit of glue but what do people do to tighten it ? Do you use a small vice ?

Second of all, I know that I'll have to cut it to length but how does one do it ? Trial and error ? Measure an approximate length and then just shorten it bit by bit until you get it right ?

Edited by Chopin
Link to comment
Share on other sites
WatchMaker Super WRT Addict

WatchMaker

Posted
Posted

I"ve used these before to good effect. I just put a crown on the extension and a drop of glue on the original stem. Now holding the original stem in a pair of pliers twist the extender on using the crown to screw it on. You don't need to use a lot of force. 

In terms of then shortening your new extended stem then approach this no differently than you would a normal stem situation. This is a great posting:

It''s sometimes necessary to shorten the original stem so that when the extender is fitted and shortened there's appropriate thread on the extender to fit the crown. Trial fit everything before the drop of glue!

  • Like 1
Link to comment
Share on other sites
Chopin Super WRT Addict

Chopin

Posted
  • Author
Posted

That is one method that I was thinking of... Thanks!

At first I'm going to try and just trim the extension and see if it works, if not then I guess I'll have to trim the stem as well.

Another question which I forgot. How and what do you use to cut the stems and extensions ?

I don't have any special such tools but I do have the tools that you'll find in a normal household... Hope I have a pair of cutters with good blades...

Link to comment
Share on other sites
digginstony Super WRT Addict

digginstony

Posted
Posted
That is one method that I was thinking of... Thanks!
At first I'm going to try and just trim the extension and see if it works, if not then I guess I'll have to trim the stem as well.
Another question which I forgot. How and what do you use to cut the stems and extensions ?
I don't have any special such tools but I do have the tools that you'll find in a normal household... Hope I have a pair of cutters with good blades...
You may get away with just trimming the extension. As mentioned by "Watchmaker" Geo's article is just about the definitive work on this subject.
Wirecutters for the stem but the type you cut straight onto rather than to the side of the stem are best.
Try Cousin's or Esslinger, as they stock replacement stems suitable for Seiko that are threaded their hole length and makes life a lot easier

Sent from my SM-T585 using Tapatalk

  • Like 1
Link to comment
Share on other sites
WatchMaker Super WRT Addict

WatchMaker

Posted
Posted

I have a pair of straight cutters ... nothing special e.g. item P36103 from https://www.cousinsuk.com/product/end-or-top-straight-cutters# . You could use normal cutters just above the desired cutting mark and then gently file down any 'peak' caused by a non-straight cut to your mark. Because extenders are so cheap (around a pound for five) you can always practice on an extender itself i.e. cut and file on an extender and then check another extender will easily screw on. This may be a better option for you than buying special cutters if this is a one off job.

 

  • Like 1
Link to comment
Share on other sites
digginstony Super WRT Addict

digginstony

Posted
Posted
I do have extra extensions and an extra stem, just in case, but I'll try not to mess it up. [emoji3] Wonder if I have any good files... Could sand paper work ?
Sand paper [emoji16][emoji16]. You'll need a decent fine cut file. Remember when sized, to bevel the tip. This prevents stripping the thread on the crown when screwing on.

Sent from my SM-G920F using Tapatalk

  • Like 1
Link to comment
Share on other sites
Chopin Super WRT Addict

Chopin

Posted
  • Author
Posted

Well, the good news is that I've managed to do anything required. The bad news is that with the extension (even trimmed out) the crown is now too long and I also broke the stem inside the crown.

Now I have to buy a new crown and stem as the old one didn't seem to actually fit, length wise, especially since I tried a brand new stem and it was a bit too short.

Oh well...

Link to comment
Share on other sites
 Share
Go to topic listing


  • Recently Browsing

    • No registered users viewing this page.

  • Topics

  • Posts

    • Neverenoughwatches
      Stem removal after fitting hands

      By Neverenoughwatches · Posted

      So leave off the seconds. Stand the movement on its edge, its the dial edge that rests on the pad ( either rubber or cork , something that wont slip ). Use a finger of your left hand to hold the movement upright,  right hand presses the release and flicks out the stem. I do it this way so i can see what I'm under a microscope. But you could hold the movement between two fingers of your left hand, its the right that has to manipulate the stem out by pushing the release and flicking out the stem with  right ring finger nail. Sounds more complicated than it actually is. I guess you could fix a push pin to something solid, then all you need to do is push the release against the pin, leaving your right hand completely free to pull the stem out.
    • HectorLooi
      Battery

      By HectorLooi · Posted

      Try putting everything back together and closing the back cover. I think one of the two springs has to contact the metal casing to ground the casing. So when you press the button, it will touch the contact on circuit board and close the circuit.
    • PeterS
      Stem removal after fitting hands

      By PeterS · Posted

      Yes, the seconds hand is the longest and goes almost to the edge of the dial. I can’t quite picture it how you do it on the rubber pad
    • Murks
      Battery

      By Murks · Posted

      A don't think so it leaked or damaged it because the watch itself works it just the buttons ain't working not connecting with the circuit board have taken more pictures of where the buttons makes contact with the circuit board.
    • Neverenoughwatches
      Stem removal after fitting hands

      By Neverenoughwatches · Posted

      I think what peter means oh is once he has fitted the hands and  checked for  alignment if them and that they dont foul, how does he then hold the movement to remove the stem in order to case up. The dial cannot be laid on a cushion or in a movement holder as the hands will get damaged. This can be quite tricky for a beginner, what i do is  to stand the movement on edge on a rubber pad so it doesn't slip. Hold the top edge with one finger then my dominant hand uses 3 fingers to press the stem release and flick out the stem. See below peter, leave off the second hand as this is the longest and gets caught the most, then fit it once the stem is out. Alternatively place the movement in one of the cup style holders, i imagine this is what they are designed for. They only touch the very edge of the dial.  
×
×
  • Create New...