Jump to content

Adjusting a broken Hairspring


jdrichard

Recommended Posts

Update: put in a balance screw i got from Cousins in a pack of 100. Went in well. Put in the second and one and IT SNAPPED OFF! Moved to another hole and the next one snapped off as well. So now mu balance has two nubbies that are leftovers from the broken screws. How do i remove these to try again and are all balance screws so soft?2669315a0d421d6bc90d58c8ce73f3be.jpg6f424eb6285c83056c224bdbd20f80f7.jpg


Sent from my iPhone using Tapatalk Pro

Link to comment
Share on other sites

Try tweezers on the inner protrusion and turn clockwise until it falls out?
Small drill and drill into stub and use new balance weight as a thread cutter?
Drill and tap and use oversize balance weights on both sides ?
All I can think of at the moment.


Sent from my SM-G920F using Tapatalk

Link to comment
Share on other sites

UPDATE. I ended up reaming out the screw and did put in two too heavy screws which really slowed the watch down. So tonight i replaced them with smaller screws and still too slow. So i moved the spring over in the stud and after a heck of a lot of spring tweeting, I got the watch withing +/- 5 seconds per day. All working well but i did forged to edge the hairspring collet over so i now have a big beat error. I am going to let it run tonight and check the time in the morning and determine if i need to address the beat error. This 1890 pocket watch is good for today:)099bb070117d670efe4df516b5753fd1.jpg&key=3b7e1bd3be776c0f45766a4aa31c2edd7613bd9fbbf8c33c9f34bb037b66c882

e640facc8d89c7a962ea7f489a67bddc.jpg

 

Sent from my iPhone using Tapatalk Pro

 

Link to comment
Share on other sites

Fantastic! I love it when a plan comes together... 11/10 for tenacity :woohoo-jumping-smiley-emoticon:
I’m sure you’ll be taking extra care while you tweak that beat error, and you may have altered the thermal compensation ever so slightly, but I doubt that will be something to worry about!

So taking out the balance staff one more time to adjust the beat error is optional. I woke up this morning and the watch was 100% accurate, so the risk is playing with it one more time. Darn!

Sent from my GT-N5110 using Tapatalk

Link to comment
Share on other sites




  • Recently Browsing

    • No registered users viewing this page.
  • Topics

  • Posts

    • I actually sent a message to him on eBay asking exactly that. They all look like snap-on casebooks so should be easy enough to get the photos.
    • I thought they were a close match to Cortebert, Nev also suggested Invar , i found a 19"' that had a very similar curved balance cock.  I looked at Revue as well but Ranfft was throwing up 404s on the pocket watch sizes.
    • Looked all over and I can't find it. Pity Ranfft movement identifier doesn't work. The closest movements I've seen, from general layout, and shape of keyless are Corterbert.
    • Well, this stickiness was only on 1 or 2 turns at first.  After using the B-Dip, I can actually manipulate the the turns in such a way that ALL of them stick on one side and I can pull them apart and you will still see a few sticking still so there is either residue from the B-dip or the initial crud that B-dip didn't remove.   What bothers me most is that I can still see liquid in-between the turns holding them together, as if the dip didn't completely evaporate.  When I get a chance, I'm going to try an alcohol or lighter fluid dip and see what happens.  I don't have a very fine brush for this, so that might have to be the next step.
    • Couple of Oris in there , early Oris were pretty small , around 28mm , the first 2 could be 45x or 49x series calibers. The Unicorn might also be an Oris, to know that these will be pin pallet watches if there is no jewel count on the dial. The other 3 will be much the same. The Oris are ok and have some value, as far as pin pallets go Oris were very good as thats all they were allowed to work with for a long time, so they made sure they got the best out of them. Its good to inside though, at the most basic level of inspection of an Ebay sale at least you can see if anything is missing inside, otherwise its just pure luck. Ask the sell if he will add some pictures of the insde for you to privately look at.
×
×
  • Create New...