Jump to content

Seiko 7T32-6L20 Macchina Sportiva

systeman

By systeman
in Your Watch Collection

 Share

Recommended Posts

systeman WRT Addict

systeman

Posted
Posted

I've been looking for one of these for a very long time. I've just got my hands on a Seiko Macchina Sportiva from the 1990's, but this one is quite rare. It's the 7T32-6L20 Black ION with its original black rubber strap.

I've given it a full service but need to realign the date ring, that's not a problem. But what is a problem is the case back.

There's video I've made to show it off a bit.

The back on these was a silicone based black finish and this had deteriorated over time. Again, not too much of a problem, I'll completely strip back the back plate to bare metal and reapply a new decal to original spec.

59353a7e61fdc_Seiko7t32-6L20-1.thumb.jpg.22fd80f3820a8f1454a82a5cf77e1dbb.jpg

 

59353a8c49787_Seiko7t32-6L20-2.jpg.da23a5e8bb1d4d0ed4c447693ebb0ca3.jpg

 

59353a97a5fc4_Seiko7t32-6L20-3.jpg.07cb572afddcb08d6907edc1984ccc25.jpg

  • Like 4
  • 2 months later...
systeman WRT Addict

systeman

Posted
  • Author
Posted

I've finally got round to redoing the case back for this watch. Now it's looking pretty good.

The original was probably a screen print over the finish. 

I used the photos of the original to redo artwork before applying it to the back.

I apologise for the blurry photo.

59aad7a30af3f_Picture144-2.thumb.jpg.6fc31b1e352f0ac302684de9a74973c8.jpg

  • Like 3
systeman WRT Addict

systeman

Posted
  • Author
Posted
23 hours ago, StuartBaker104 said:

How did you do that? It looks great!

I took a photograph of a few Macchina Sportiva case backs and took measurements of the text, the logo panel and diameter of the text relative to the panel and case back.

I then edited and recreated the Logo panel in Gimp.

I recreated the circular text using the same font as a layer.

Then I created a black background layer the same overall size of the case back.

The artwork was the laser printed onto a transfer film ready for transferring to the case back.

Obviously, printers do not print white text. Therefore, I used an acid etch primer on the case back before painting it with an off white background for the text.

The transfer was then applied and baked on. A few coats of matte lacquer was then applied to seal and finish it off.

This is not one for the faint hearted, it needs a lot of patience.

  • Like 3
PJA WRT Addict

PJA

Posted
Posted
13 hours ago, systeman said:

I took a photograph of a few Macchina Sportiva case backs and took measurements of the text, the logo panel and diameter of the text relative to the panel and case back.

I then edited and recreated the Logo panel in Gimp.

I recreated the circular text using the same font as a layer.

Then I created a black background layer the same overall size of the case back.

The artwork was the laser printed onto a transfer film ready for transferring to the case back.

Obviously, printers do not print white text. Therefore, I used an acid etch primer on the case back before painting it with an off white background for the text.

The transfer was then applied and baked on. A few coats of matte lacquer was then applied to seal and finish it off.

This is not one for the faint hearted, it needs a lot of patience.

Great job and very creative!

  • 2 weeks later...
systeman WRT Addict

systeman

Posted
  • Author
Posted

I've now uploaded a video of the finished watch:

It was great fun getting involved with refurbishing the case back. After assembling and testing the functions, I did notice an improvement in the volume of the buzzer. This was probably because of baking the decal. The process must have improved the conductivity of the old adhesive.

  • Like 1

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Restore formatting

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

×
 Share
Go to topic listing

  • Similar Content

  • Recently Browsing

    • No registered users viewing this page.

  • Topics

  • Posts

    • docrpm
      Elgin Grade 315: Runs/stops with dial down/up

      By docrpm · Posted

      Yep…This makes perfect sense. With that large a gap in the serial numbers, they were almost certainly machined on different equipment, hence one should have no expectation of any cross-batch compatibility. I’ll revert to the original bridge. Regarding bending the bridge @nevenbekriev, I’ll give it a try, but I may have to buy some better calipers. My Vernier calipers are only accurate to 0.1mm. Not very accurate. 
    • nevenbekriev
      Elgin Grade 315: Runs/stops with dial down/up

      By nevenbekriev · Posted

      Yes, what I wanted to say is that the cock is part of the main plate, manufactured together with it and not meant to be interchangeable. Even if the other cock gets in place, it is not sure that the balance then will stay upright. You should use the original cock when it exists and is not destroyed. The adjustment needed by bending it is not irreversible. It is minimal deforming that is needed. No tools are needed. I have pointed to all needed references here for the balance staff endshake checking and correctness confirmation. The only tool needed for the correction is You thumb. The cock must be fixed on the main plate, no need of special plate with holes and so on. If You will feel more confident, then measure with Vernier caliper the height of the top of the cock where the stones are against the main plate bottom when the shim is fitted and try to reach the same height when bending the cock (with no balance in place!!!) Caliper with screw for fixing is perfect.    
    • LMS
      Thermal Bluing Issue

      By LMS · Posted

      Thanks for the reply. I polished the head of the screw using 1500 to 10000 lapping paper and a screw polisher. This is why I think the head blued and the rest of the screw didn't. Silly question, how do you polish the whole screw inc threads, if that's what it needs to blue? 100% clean, Elna red and heated ultrasonic bath + IPA rinse. Finally, there is definitely heat leak as there's about a 30c difference between the brass bed and the soldering station temp. Having said that, the bed temp was stable. I will try to search out a better brass pot, but I haven't found one yet, hence the stainless steel bowl. 
    • RichardHarris123
      Removing stem from compressor-style case

      By RichardHarris123 · Posted

      Agreed but that's where WD40 excels, water displacement. 
    • tomh207
      Thermal Bluing Issue

      By tomh207 · Posted

      I would change the container to a thick walled brass one to start with. Looking at you screw pictures they don’t look shiny enough, really it’s best to do a black polish on them before trying. Also make sure once polished they are scrupulously clean, I dunk my experiments in acetone before bluing.   i think the thin walled stainless container to leach away the heat from the shavings, most successful bluing videos for example use thick walled brass to hold a good deep amount of shavings which acts as a better holder of heat.   Tom
×
×
  • Create New...