Jump to content

Bad start to 2017


clockboy

Recommended Posts

It,s was my fault I left my workshop ajar last night and found our cat asleep on the window seal this morning. Had a quick check around the bench and nothing was broken and looked ok then !!!!!! I stepped on this wheel. It is from a very cheap (wife paid £5 for it at a fair) Enfield Smiths westminster chiming clock. I have posted a couple of pics of me trying to straighten the pinion and it is almost straight but I can not see how I can rivet the wheel back on as my punches are not deep enough to fit over the length of the pinion. IMG_1046.jpgIMG_1047.jpgIMG_1053.jpg

Link to comment
Share on other sites

Good idea Mark yes I have one so I will give it a try. Getting the shaft absolutely straight will be the next challenge

What fun !!!!!



Lol

Good luck - I have every confidence you will repair. :)


Sent from my iPhone using Tapatalk
Link to comment
Share on other sites

Here's another idea, create a larger seat for the wheel.

Make a brass collar that you secure onto the arbor that has a wheel seat centered over the old position. The seat itself will be larger in diameter than the old seat to give it strength. Secure it with locktite. Chuck up the arbor and turn a new seat and a decorative back end.

Once its made  mount the wheel in a pot chuck to open the center hole to fit the new seat diameter. Stake it on normally.

Al Takatsch

 

Link to comment
Share on other sites

2 hours ago, oldhippy said:

Can't you drill the stake out. Its a very common movement as you know so there shouldn't be a problem.

I did think of that but I presume the stake will be hardened steel. I have found some Clock punches in various supply houses wondering if the holes are deeper to allow for the pivots.

Link to comment
Share on other sites

1 hour ago, altaka said:

Here's another idea, create a larger seat for the wheel.

Make a brass collar that you secure onto the arbor that has a wheel seat centered over the old position. The seat itself will be larger in diameter than the old seat to give it strength. Secure it with locktite. Chuck up the arbor and turn a new seat and a decorative back end.

Once its made  mount the wheel in a pot chuck to open the center hole to fit the new seat diameter. Stake it on normally.

Al Takatsch

 

Thats also a good idea but will I have the issue when staking the new seat i.e. the pinion is to long for my punch.

Link to comment
Share on other sites

Well I suppose I could but the stake has to be domed & hardened. This is possible but a big job for a clock that cost £5. However if I can get the pivot absolutely straight I will try to solder the wheel onto the pivot.
Family commitments for the next few days but will keep you guys informed of the progress (if any!!) 

Link to comment
Share on other sites

7 hours ago, altaka said:

I have a lot of Rebarb steel used to strengthen concrete. 1/2 inch would do it and its soft. It will turn quick in a lathe.

Do not need to harden it because you are staking brass to brass

Al T.

Thanks family commitments stopping progress for a couple of days. Lots of options suggested with this but the priority is to get the pinion absolutely straight because other issues will surface if not.

Link to comment
Share on other sites

12 hours ago, altaka said:

I have a lot of Rebarb steel used to strengthen concrete. 1/2 inch would do it and its soft. It will turn quick in a lathe.

Do not need to harden it because you are staking brass to brass

Al T.

Don't you mean rebar steel.

Link to comment
Share on other sites

Just an update with this. I just could not get the pinion perfectly straight & also I found the wheel was also out of true. I did a an experiment for future reference & soldered the wheel to the pinion which works a treat so a useful exercise.

However I have now purchased a donor movement for the replacement wheel. 

What fun!!!!

Link to comment
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Restore formatting

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.



  • Recently Browsing

    • No registered users viewing this page.
  • Topics

  • Posts

    • H Watch Repairers—is there is a ‘standard format’ for the service marks or codes lightly engraved inside cases of pocket watches or wristwatches?   Sometimes I can see there might be a reference to year/ month but other times am confused. I’ve included an image of the rear of a 1951 Hamilton 992B Railroad pocket watch as an example. Thank you for all information you can give, Mike
    • Hi to Blackminou29–am a collector/ caretaker—good luck to you following your repair course—with hindsight I wish I’d pursued a career in both watchmaker/ jeweler fields—good luck with whatever career passion you engage.   Thank you Watchweasol for posting the amazing TZIllustratedGlossary! Best wishes, Mike
    • yes I noticed the new site and I miss the old site. It's the unfortunate problem of the Internet here today gone tomorrow sometimes some of the stuff gets backed up and sometimes well it does not then the problem with the early Seiko's were there were not necessarily designed for distribution across the planet and as such there is no customer support for them. So trying to find early stuff like technical information or sometimes even parts list for older Seiko is is problematic. But I did find you a you tube video. A quick look he seems to take a heck of a lot of time to actually get to the service single I did not watch all that but it does look like he did disassemble or started to say there's a tiny bit here  
    • RichardHarris123: Hello and welcome from Leeds, England.  I have family all over Australia, went as £10 poms Thanks Richard. Hope you’re able to visit your family here and that they’ve all done well 🙂 My relatives arrived from England in the 1790s transported on the ‘Second & Third Fleets’—a story of timber sailing ships, of convicts and doing well in this huge Country of Australia. When I visited the UK in the 1980s, I was too young to comprehend the depth and breadth of its history…  Best wishes, Mike William Chapman, my 4th great Grandad’s charges, at age 23 read at the Old Bailey; sentenced to 7 years of transportation to Sydney.
    • The whole process and the progress are closely observed, it's hand-driven and very controlled. I can't see the "danger", unless you are watching the TV while doing it. As you could have read, and in this quote "wheel" is the balance-wheel.
×
×
  • Create New...