Jump to content

Greetings from Amsterdam

Jorick

By Jorick
in Introduce Yourself Here

 Share

Recommended Posts

Jorick New Member

Jorick

Posted
Posted

Hi all!

From the Netherlands, Amsterdam, i'd like to say hi as a beginning watch enthusiast. 
I'm a proud owner of a Frederique Constant, Aerowatch and a couple of Sea-Gulls. 
But, i found out that there is more than wearing a nice watch, the complication behind it 
is even more interesting! I therefore bought some instruments to demount and
assemble a movement:). And perhaps (hopefully) later on assemble my own watch with different components.
I therefore use the youtube watch repair channel to gain myself the basic information, many thanks for these interesting videos!

Little question to end my introduction though, does anyone know which movement I can 
buy to demount and assemble the Rotary AS 1900? In fact, which movement can be compared mechanicly the same
as the AS1900, and doesn't cost a fortune. Cause I will use it as an assemble movement. (by using the AS1900 service video I want
to take the movement apart and assemble it back again to learn how the movement works).
 

Watch regards!

Jorick 

Link to comment
Share on other sites
Cad101 Super WRT Addict

Cad101

Posted
Posted

AS1900 is a nice movement but if your just srarting this facinating hobby you really don't need to buy expensive unless money is no object to you a cheaper running movement of the bay will suffice just remember to take a photo at each step of the breakdown and remember to place the parts as you dismantle them in a separate partition in one of those plastic partitioned containers, then you can keep parts that go with each other together. And once you've cleaned your parts just work backwards through your tray and pics. Oh and hello btw have fun.

Mick

Link to comment
Share on other sites
bobm12 Distinguished Member

bobm12

Posted
Posted

Welcome Jorick! As our friends above just said, no need to start with an expensive movement. Although it might seem a worn out advise, I would say, start with a simple, big movement like the ETA 6498 which can be had on ebay for about 40. Make sure it works so when you are done, if it still works, you know you are doing fine. Then, you can buy from the same ebay a case and other "periferals" :) and build your own watch with that movement.

Cheers,

Bob

Link to comment
Share on other sites
  • 2 weeks later...

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Restore formatting

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

×
 Share
Go to topic listing


  • Similar Content

  • Recently Browsing

    • No registered users viewing this page.

  • Topics

  • Posts

    • HectorLooi
      Battery

      By HectorLooi · Posted

      Try putting everything back together and closing the back cover. I think one of the two springs has to contact the metal casing to ground the casing. So when you press the button, it will touch the contact on circuit board and close the circuit.
    • PeterS
      Stem removal after fitting hands

      By PeterS · Posted

      Yes, the seconds hand is the longest and goes almost to the edge of the dial. I can’t quite picture it how you do it on the rubber pad
    • Murks
      Battery

      By Murks · Posted

      A don't think so it leaked or damaged it because the watch itself works it just the buttons ain't working not connecting with the circuit board have taken more pictures of where the buttons makes contact with the circuit board.
    • Neverenoughwatches
      Stem removal after fitting hands

      By Neverenoughwatches · Posted

      I think what peter means oh is once he has fitted the hands and  checked for  alignment if them and that they dont foul, how does he then hold the movement to remove the stem in order to case up. The dial cannot be laid on a cushion or in a movement holder as the hands will get damaged. This can be quite tricky for a beginner, what i do is  to stand the movement on edge on a rubber pad so it doesn't slip. Hold the top edge with one finger then my dominant hand uses 3 fingers to press the stem release and flick out the stem. See below peter, leave off the second hand as this is the longest and gets caught the most, then fit it once the stem is out. Alternatively place the movement in one of the cup style holders, i imagine this is what they are designed for. They only touch the very edge of the dial.  
    • PeterS
      Stem removal after fitting hands

      By PeterS · Posted

      Yes I understand that. What I’m asking is, after the hands have been fitted, it’s been checked that the hands do not touch etc. then I need to remove the stem to fit the movement in the case. I have the push type, I need to turn it upside down and push the setting lever post and pull the stem out. But of course the dial and hands are in place and I have a glossy dial with lume dots and I do not want to cause any damage while it’s upside down pushing on the post of the setting lever.
×
×
  • Create New...