Jump to content

New Member

NigeH

By NigeH
in Introduce Yourself Here

 Share

Recommended Posts

NigeH New Member

NigeH

Posted
Posted

Hi all just a note to say hello , just starting out have been making gold a silver jewellery for a long time but would like a new challenge . Not sure where to start so any advice welcome .

Link to comment
Share on other sites
oldhippy Distinguished Member

oldhippy

Posted
Posted

Hello from me. Making gold and silver jewellery. You are going to used to handling small parts for a start which is good. Plenty on here as to how to go about starting. The first is to get yourself good tweezers and screwdrivers and eye glasses. Don't buy cheap as they won't last.

Link to comment
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Restore formatting

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

×
 Share
Go to topic listing


  • Recently Browsing

    • No registered users viewing this page.

  • Topics

  • Posts

    • Bonefixer
      Waltham A-11 Hairspring and Balance assessment help needed.

      By Bonefixer · Posted

      Newbie here too, but I’ve done a bit of reading around this subject. Looks like a Breguet overcoil. You’re right about A and B - A is just a minor tweak - but most damage is between B and the stud.    Pivots can be unbent, but there’s a high risk of breaking it off. Take care, and probably see how it runs before trying.    That’s really dirty. I’ve never found IPA to loosen Shellac. If you’re worried, put it in soapy water in the ultrasonic and then dip it in IPA as a quick rinse to displace the water and prevent rusting.    As for the stud - does it wedge in the angle and the screw holds it there?
    • Mark
      Spell Check

      By Mark · Posted

      No, it is browser dependent - your browser may have a spell checker you can switch on in settings. A quick search on Google may help you if you don't use Chrome: https://support.google.com/chrome/answer/12027911?hl=en-GB
    • Waggy
      How to store one dip

      By Waggy · Posted

      Good to know, I'll move that to the bottom of the list
    • oldhippy
      Spell Check

      By oldhippy · Posted

      What you can do is type it in say Microsoft Word use the spell check in that then cut and paste it here. 
    • Zendoc
      Replacing armoured crystal in a front loading watch case…

      By Zendoc · Posted

      Thank you for your reply, Curare.  You offer me hope ! Yes, my experience is that crystals with a tension ring require a very heavy screw down on the crystal lift - I’ve cracked a couple.  I think I’ll use a press to install the new crystal and keep my fingers and toes crossed that I don’t mash the underlying dial and movement. Waggy - there’s no bezel on this particular omega case and the movement loads from the front (there’s a spit stem), so the only option is to directly fit the crystal into the case with the movement in place.  And what happened to you could so easily happen to me!  I have woken in my sleep, heart racing,  seeing the fragments of smashed crystal gouging the dial and mangling the hands! I’m hoping someone who has worked on an Omega Dynamic might have some direct experience and will let me know how they managed the surgery. Thanks to all. Cheers, John   Oldhippy - thanks for your comment.  So, you’d just go ahead and place the crystal using a press, movement in situ, in the case?  OK - that’s what I’ll do.   Cheers, John
×
×
  • Create New...