Jump to content

Replace broken balance staff

buzz12

By buzz12
in Watch Repairs Help & Advice

 Share

Recommended Posts

bobm12 Distinguished Member

bobm12

Posted
Posted

Does it look like this?

View picture in original size
If it does, it is a Ronda 1213...So knowing this you may be able to locate the staff from different suppliers...if it exists.

Geo mentioned a link in another post where you can order about any staff you need. Maybe he will post it here later. I don't remember it, though. In the meantime you can check CousinsUK and others.

Cheers,

Bob

  • Like 1
Link to comment
Share on other sites
buzz12 Watch Enthusiast

buzz12

Posted
  • Author
Posted

Thanks Frenchie, I have seen it... very useful. I fancied having a go but it looks like £20 for the staff, which sadly this watch is not worth the expense. I'll have to find a more worthy candidate me thinks.

Link to comment
Share on other sites
 Share
Go to topic listing


  • Similar Content

  • Recently Browsing

    • No registered users viewing this page.

  • Topics

  • Posts

    • VWatchie
      My polishing achievements so far

      By VWatchie · Posted

      I remembered that when Lititz Watch Technicum's YouTube channel existed, they had a video about polishing. As I recall, many experts thought that video was among the best on the subject of polishing. It's a real shame that their videos are no longer available and I've been in touch with them regularly to see if they can get these videos back. Unfortunately, it seems that these videos are gone forever. The last message I received from them on 21 January read: "I'm sorry, but not yet. In a nutshell: the school is scheduled to be shut down next year - a new school is bring opened in Dallas, Texas. Because of that all video access is blocked. If a decision is made to not close the school, then at some point the videos will likely be made available. We just do not know that yet. So, just check in again in a month or three; sorry I can't be more specific than that." Well, as I recall, there was a section in the video that was about how to preserve the edges of a watch case, that is, how to avoid rounding off the edges when using a mop wheel. I don't remember all the details but what I do remember is that it's about keeping a high speed on the mop wheel and keeping a light pressure on it. I didn't think of this when I was polishing the case back but the next time I'll try it and see what difference it makes.
    • RichardHarris123
      Case Tube Tool - Quest for one that works

      By RichardHarris123 · Posted

      Good idea, I  was thinking of something similar but using a drill press.  Apologies, all the other comments have just appeared.  I was replying to @HectorLooi , the chain pusher is a good idea too.
    • Neverenoughwatches
      Case Tube Tool - Quest for one that works

      By Neverenoughwatches · Posted

      Now thats a real man's tool press 👍. I have one just like it in my back garden for when just CANT fix a watch . Its not something i have had to do yet, @Waggybut wouldn't any type of press be able to do this ? What about an adapted chain link  extractor work or a micrometer with some sleeve pushers made to slot over the ends. @Waggy Found something that could work Scott, comes with different size pins and pushers. Only bit that would need making is a round former to support the inside of the case, a piece of stout timber, bit of oak or mdf might do it. What i like about this one is the pin is pushed in, its in a sliding sleeve so it doesn't turn while its being driven. This has 4 pin sizes and 3 stumps as well so it will come in for other applications, the pins could be adapted to take other accessories from jewelling tools. I've just ordered one myself for some play time. 
    • Mperss920
      Seiko 6309a diver crown replacement

      By Mperss920 · Posted

      So I purchased this one based on my case number being listed. (Unless my case number is incorrect. The last digits are faint)
    • HectorLooi
      Case Tube Tool - Quest for one that works

      By HectorLooi · Posted

      I have the same tool from AliExpress and get the same anxiety when when using it. But you have to admit it looks awesome on your tool shelf. Makes you look like a pro. 🤣 Looking at the photo of the Horotec tool, it looks equally flimsy. It probably comes from the same factory. I was thinking of using the pushers supplied with the tool and making a hand tool from a cranked jeweller's punch. I'll grind off the tip of the punch and drill a hole at the end to fit the pusher in. The cranked shank would be able to clear the watch case give a straight in-line axis to exert force to tap the pendant tube out. Should be robust enough to last several lifetimes. I wonder why nobody makes it. 🤔
×
×
  • Create New...