Jump to content

K&d Tool

toptime810

By toptime810
in Tools & Equipment

 Share

Recommended Posts

Ishima Super WRT Addict

Ishima

Posted
Posted (edited)

I think you did well, no comment on the pocket watch. (if it doesn't go on a wrist, don't ask me)

But that looks like a rather comprehensive, and mostly complete, well maintained staking set. I thought it might have been a bit rusty in your second picture but I realized that was just a tungsten lighting issue. Withought being to verify it all works well and precisely, I say you got a deal. Staking sets are one of those glorious things that can set you back a fortune brand new and you can pay very little for them second hand. They're dead handy for certain things.

I got my self a complete 'Star' (vintage bergeon) staking set from Ebay for £90 (bout $120) that brand new costs around about, maybe just shy £1,000 (~$1,500). And I don't expect to strike a deal quite that good again. I'm not sure what a brand new K&D staking set would cost you, or if they're even still manufactured, but I would have bought that. 

Also, the box is rather lovely too. 

Edited by Ishima
Link to comment
Share on other sites
Joeydwatchmaker Member

Joeydwatchmaker

Posted
Posted

A k & d inverto complete 18 for that price is a good deal. I got one similar a while ago for around the same price. I really did not need the jeweling attachments as I have a seitz complete set which I feel is better set than the 18 jeweling attachment. I think you did very well there. Good luck there is so much you can do with that set.

Sent from my iPhone using Tapatalk

Link to comment
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Restore formatting

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

×
 Share
Go to topic listing


  • Similar Content

  • Recently Browsing

    • No registered users viewing this page.

  • Topics

  • Posts

    • VWatchie
      Epilame / Fixodrop

      By VWatchie · Posted

      But it also makes it seem less susceptible to gravity. If you place a droplet of oil on an epilame-treated surface the droplet of oil will still stay in place even if you then flip the surface from a horizontal to a vertical position. That is, the oil droplet remains anchored, and that's the purpose of epilame. If it was just a matter of creating an oleophobic surface we could probably use other, less expensive, methods!?
    • Michael1962
      I'm going to be setting up a decent little workshop here at home.

      By Michael1962 · Posted

      Saturday morning 27/4 Sunday evening 28/4 Monday evening 29/4 Floor has a drain in the middle so I am hoping that there is very little fall on it, if any. Room is about 2.5 x 2.5 metres square. Can only use about 1/2 of one wall on the right of the pictures which has a sliding glass door in it. And only about 3/4 of the wall to the left of the pictures as it has the door to the house in it. Progress. 🙂 
    • Neverenoughwatches
      Epilame / Fixodrop

      By Neverenoughwatches · Posted

      This makes much more sense now, the oil is withdrawing itself to make as little contact with the epilame as possible. Same principle as wax on a car creates a hyrophobic surface that makes the cohesive properties of water molecules pull together.  The water beads run off only when under the influence of gravity but still remain cohesively beaded up. And as mentioned earlier a pivot would keep the oil in place on a cap jewel.  Epilame on an escapement would be a different scenario, there is nothing to hold the oil in position if gravity tugs at the bead to move, plus the escape teeth pull the oil about Maybe this is why its suggested to run the watch for a short while to remove the epilame to make two oleophobic surfaces either side of the oil, creating a ring of fire 🔥 around it 😅 The oil is repelled by every surface of the epilame even that which it sits upon. So the oil pulls together to make as little contact with it as possible, but the oil cant float above that area, it can only sit there on top of it. Under gravity the oil could potentially run away as an oil bead, unless the epilame has an adhesive property which i dont think it does ? So something else keeps it in position ie a pivot under a cap jewel . But that isn't the case in a pallet jewel situation. 
    • mikepilk
      Balance wheelwheel crooked

      By mikepilk · Posted

      As with every skill it watchmaking, it takes practice. Notice at the top of the document it says, "Practical work - 40 hours".  I can get the balance wheels 'close enough' to flat, but never seem to get them perfect. Same with gear wheels. Guess I need more practice.
    • transporter
      Beat adjustment

      By transporter · Posted

      Has it got a beat adjustment on the platform or is it a fixed hairspring? in short what you are looking at to get it just about in beat is to get the roller jewel sitting dead centre between the banking pins. So remove the platform and take of the pallet fork and escape wheel to give you clear line of site, sit the platform with the balance in place and with it level look between the banking pins and see if the roller jewel is sitting between them, if it is nice and central its there or there abouts in beat, if its not the the position of the pinned end of the hairspring needs to be adjusted to move the roller jewel into the correct position, thats why I asked if it has an adjustment on the platform or not, if it has its an easier job. 
×
×
  • Create New...