Jump to content

Recommended Posts

Posted

I've got a newbie question here.  How do you store one dip to prevent evaporation?  I thought that was the point of putting it in a glass jar.  I was obviously wrong.  After a week or 

so it was gone and this stuff ain't cheap.  Any tips to prevent this evaporation is appreciated.

Posted

Purchase the jar for using its because it's very convenient the have a smaller jar. Purchase the solution in a can. I can has a metal lid and in addition to that like a metal stop her that's a pain in the ass to get out. But it's presence helps to keep it from evaporating then when you put the lid back on you have a piece of sheet plastic like a plastic bag in plastic to put that down first and screw the lid on and that seems to keep it in the can for quite a long time. Then from time to time you can put it in the jar.

Posted
  On 6/8/2023 at 5:05 PM, grsnovi said:

This is the sort of jar you need: a laboratory grade jar with a ground glass stopper. Only pour enough in to allow the liquid to just cover what you're planning on rinsing (pallet fork, hairspring, etc...). I don't expect it to store in the jar but it will likely keep a few days. The jar I got has a 35ml capacity but I never pour that much in.

 

jar for 1 dip.jpg

Expand  

This is what I use. I also wipe a very thin layer of silicone grease around the rim of the lid. When I used to work in a lab we would also use Parafilm around the junction of the lid and jar to seal and help stop evaporation.

  • Like 2
Posted

One of the best ways for storing anything is  in the container it comes in for instance the picture posted by @LittleWatchShop Is the candidate comes in perfect storage container.. Then the only modification to the can is  thin sheet of plastic before you screw the lid down. In the candidate seems to last a very long time

The end  when I'm actually using it I have it in the 2 ounce jar and I only put a little in the bottom of the jar.. I think it almost is never evaporated out of the jar unless somebody forgets to tighten the lid.. Which happens at work because other people use my jar. I have a picture I swiped off the website down below So they can see what the jar looks like.  So having the can for storage and the jar for use the system works quite well

cl-500.jpg.022eccd7fb4f4d76ff919e20894b964c.jpg

https://www.stsupply.com/one-dip-hairspring-cleaner-2-oz.html

 

 

 

 

Posted
  On 6/9/2023 at 7:50 AM, oldhippy said:

🤣🤣🤣

I found one dip to be utterly useless. I soon when back to Ronsonol lighter fluid. 

Expand  

Since nobody has asked OH i guess everyone knows besides you where the welly boots fits into this or more accurately what fits into the wellies. Feel free to ask for an explanation if anyone IS unsure 👍

  • 3 weeks later...
Posted (edited)
  On 6/9/2023 at 7:50 AM, oldhippy said:

I found one dip to be utterly useless

Expand  

I guess I came too late to the horological party to savour the delicate aroma of One Dip. Cousins have it listed as no longer available, to be replaced with "B-Dip" also by Bergeon. At £1.44 per millilitre, it must be one of the best value Bergeon products ever made! Does anyone have any experience with this? Is it better / worse than Renata? Does it melt your genitalia if spilled in your lap? Or is Old Hippy's Ronsonol the elixir of life?

Edited by DrHWO
Spilling mysteak
Posted

I got a big bottle of hexane to clean the balance hair spring, and it works a treat. Before treating with hexane I put the balance back on the main plate after I have disassembled the movement and run it through the watch cleaner with the rest of the parts, then take it off the movement and (once dry) put it into a my small jar (small hotel jam jar) of hexane whilst I build the watch up. It dries in air in seconds and is then ready to go onto the watch.

If I can't run the balance safely through the watch cleaner, I will soak in naphtha first as per @oldhippy suggests (naphtha being the main constituent of lighter fluid) and then once dry soak in hexane as above... Probably 'belt and braces' but it seems to work and if it 'ain't broke, don't fix it'.

Hexane evaporates very quickly, faster than acetone, so you can't hang around with the lid off, or have a leaky seal. I am also told it is safe on shellac, but haven't tested myself, but my results to date would support that it is safe. Like I said, to date I have had good results and will continue to use this method.

Hope this helps.

  • Like 1
Posted

Looks like Amazon have "N-Hexane" 95% for £25 per 500ml, so that's 5p per ml (28 times cheaper than Bergeon). Sounds impressive.

Posted (edited)

I use Hexane to rinse all the parts, including the pallet fork, instead of IPA as it's shellac safe.

I use tetraclorethilene instead of One Dip (triclorethilene), that I buy at 10€ per litre and works great.

Edited by aac58
Posted
  On 6/29/2023 at 12:49 AM, DrHWO said:

Looks like Amazon have "N-Hexane" 95% for £25 per 500ml, so that's 5p per ml (28 times cheaper than Bergeon). Sounds impressive.

Expand  

I nearly went for the Hexane but decided to choose the more traditional and health risky stuff of perc otherwise known as tetrachloroethylene. It arrives tomorrow.  Obvious safety measures will be followed.

  On 6/29/2023 at 12:49 AM, DrHWO said:

Looks like Amazon have "N-Hexane" 95% for £25 per 500ml, so that's 5p per ml (28 times cheaper than Bergeon). Sounds impressive.

Expand  

I'm curious to known what the remaining 5% is made up from Doc

Posted
  On 7/3/2023 at 7:46 AM, Neverenoughwatches said:

I'm curious to known what the remaining 5% is made up from Doc

Expand  

That would be slugs and snails and puppy dog tails as they nicely counteract the carcinogenic effects of tetrachloroethylene. Or does that only work for the dextro isomer of hexane?!

  • Haha 1
Posted
  On 7/3/2023 at 4:48 PM, DrHWO said:

That would be slugs and snails and puppy dog tails as they nicely counteract the carcinogenic effects of tetrachloroethylene. Or does that only work for the dextro isomer of hexane?!

Expand  

I best get digging in my garden then as it arrived today, but as I'm very much a dog lover i will need a substitute for the other ingredient. Bull's pizzle ? They're readily available. 

  • Like 1
Posted

From some posts I have seen the original one-dip was trichloroethylene, but the current Bergeon version is now 99.4% tetrachloroethylene aka as perchloroethylene or perc. Buying this as the generic chemical >99% rather than the branded one-dip should save a heap of cash, and then some!!, without sacrificing quality.

Would be interesting to see how each compares against the other in a shoot-out' and maybe even throw in hexane as a 4th option?

I assume trichloroethylene was replaced with tetracholoroethylene due to its lesser effects on health?? but does this sacrifice its effectiveness?

Posted
  On 7/3/2023 at 7:59 PM, Waggy said:

From some posts I have seen the original one-dip was trichloroethylene, but the current Bergeon version is now 99.4% tetrachloroethylene aka as perchloroethylene or perc. Buying this as the generic chemical >99% rather than the branded one-dip should save a heap of cash, and then some!!, without sacrificing quality.

Would be interesting to see how each compares against the other in a shoot-out' and maybe even throw in hexane as a 4th option?

I assume trichloroethylene was replaced with tetracholoroethylene due to its lesser effects on health?? but does this sacrifice its effectiveness?

 

Expand  

Not easy to find this information out even less easy to understand.  Tetrachloroethylene ( a chlorocarbon ) did replace trichloroethylene ( a halocarbon ) was also used in making pesticides and refrigerants . Apparently the trichloroethylene had a stronger cleaning ability but higher health risk. Cheaper than hexane this litre was 22 quid. 

  • Like 1
  • 9 months later...
Posted

I was looking at Essence of Renata, a chemical used a lot for cleaning hairsprings:

"Specially prepared solution for degreasing watch and instrument components. Indispensable for degreasing hairsprings."

Looking at the MSDS you can see this is just pure n-Heptane, so could be an option for those who don't want to use the chlorocarbons or hexane?

 

 

HF6013 - Horological Essence COSHH Safety Data Sheet Horological Essence_0.pdfFetching info...

  • 2 weeks later...
Posted (edited)

So I checked with my friendly local lab supplier and they can supply the following in 2.5 lt bottles:

  • Tetrachloroethylene (B-Dip) - approx £65
  • Trichloroethylene (one-dip) - approx £43
  • n-Heptane 99% (Essence of Renata) - approx £35
  • Hexane - approx £45

I can't import or buy locally the 'real' products, hence the raw chemicals above. What do you think would be my best option?

I'm edging towards Trichloroethylene - I know there are greater health risks, but given the very small quantities used for each treatment and 99.99% of the time it will be sealed in a jar, I think any risk is vanishingly small? This is mainly due to its assumed superior cleaning properties, or from the experience of this group, is the extra cleaning noticeable compared to its safer alternatives?

Edited by Waggy
  • Like 1
Posted
  On 5/6/2024 at 4:23 AM, Waggy said:

So I checked with my friendly local lab supplier and they can supply the following in 2.5 lt bottles:

  • Tetrachloroethylene (B-Dip) - approx £65
  • Trichloroethylene (one-dip) - approx £43
  • n-Heptane 99% (Essence of Renata) - approx £35
  • Hexane - approx £45

I can't import or buy locally the 'real' products, hence the raw chemicals above. What do you think would be my best option?

I'm edging towards Trichloroethylene - I know there are greater health risks, but given the very small quantities used for each treatment and 99.99% of the time it will be sealed in a jar, I think any risk is vanishingly small? This is mainly due to its assumed superior cleaning properties, or from the experience of this group, is the extra cleaning noticeable compared to its safer alternatives?

Expand  

I bought a litre of perc (tetrachloroethylene ) for 20 quid. I cant say I'm particularly impressed with it.

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Restore formatting

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.



  • Recently Browsing

    • No registered users viewing this page.
  • Topics

  • Posts

    • Making a stud pin for a pocketwatch from 1mm copper wire, softer than brass but it will do the job. The lathe cost 3 pound including the chuck, powered from an old electric shaver adapter. 
    • And I'm already very pleased with my life choices...
    • Demagnetizers work on the principle of a decaying magnetic field. Whether the expensive Elma or the cheap Chinese...same principle. For the cheap ones, you are decaying the magnetic field manually by drawing the watch away from the demagnetizer while it is energized. The Elma (and others) generates a decaying magnetic field electronically so you don't have to do the work. If you use the cheap ones properly,  they will do the job. I prefer the Elma style...but that is just me.
    • I also still use my cheap first set of screwdrivers. I replaced the blades of the smallest (0.6mm) with higher quality once I had bent a few of the originals, but beyond that I have been fine. Note though that I do not work on any remotely valuable watches and most of what I deal with are in a truly terrible state, watches that have been banging around in kitchen drawers or toolboxes. So my concern for screw head slot integrity and scratches is usually not very high.  As for a loupe - you won't need anything powerful for an ST36 that is new. You don't need to do close inspection of balance pivots because they will not be worn out, and a 3x or 5x loupe is perfectly sufficient to see the oiling. I don't have any microscope or powerful magnification of any sort. I just use cheap loupes. But again this would be different if I were working with more valuable watches. And if I had equipment to burnish pivots, then I would get a microscope to check my work.
    • I've recently switched over to using a x2.5 -x3 eyeglass for disassembly and some larger part assembly. It's interesting to see how accustomed and trained your eyes become to that way of working after using a microscope for years. And pick up and work at eyelevel when possible. Personally I would stick with and learn to use regular oilers efficiently. 
×
×
  • Create New...