Jump to content

A Minor Victory With My Grass

Mark
 Share

Recommended Posts

Mark Distinguished Member

Mark

Posted
Posted

The grass has been getting a bit long the past two weeks because the mower died. (Wife is convinced it's an excuse).

 

Anyway, I fitted a new carb today with gaskets and new spark plug. Had to adjust the ignition coil as it was fouling, but eventually got it started - it's running like a dream now.

 

I came in with a big grin with triumph and my wife just says "You need to trim the edges"!!

 

I need beer :D

  • Like 1
Link to comment
Share on other sites
canthus Super WRT Addict

canthus

Posted
Posted (edited)

Research Octane Number - a measure of the ignition point of an (unleaded) fuel (gasoline/petrol).  The point at which the engine starts to knock when the ignition timing is retarded.  Typically 91-95 these days but some 98 for high performance engines and above 100 for racing engines.  For diesels it is the Cetane Number.

Must get out more!! Perhaps mow the lawn!!

Edited by canthus
Link to comment
Share on other sites
bobm12 Distinguished Member

bobm12

Posted
Posted

 

Petrol loses its RON rating as it ages.

 

 That's true, my neighbor Ron can never be found when I do the lawn, especially when I skip some weeks!  :)

 

Just can't resist! Lawn and mowers have never been too high in my to do list...unless the wife pushes for it...then, I have to scramble! :)

  • Like 1
Link to comment
Share on other sites
canthus Super WRT Addict

canthus

Posted
Posted

Sorted a few of my mates' mowers with same problem when first used after winter lay-up.  Invariably water in the carb bowl.  Normally caused by leaving the fuel tank with fuel in it when laid-up, which then gets water in it due to condensation through changing temps (day/night, warm/cold day).  This settles to the  bottom (fuel is lighter) where it is picked up and sent to the carb (via a filter maybe which also gets water in it).  The fuel will also degrade slightly but should still work after 2-3 months.  Easiest way to avoid is to drain the fuel tank and if possible empty the carb bowl and any inline filter, before laying up, or drain them before starting for new season.  Not had problems when this is done.  Normally this is advised in the owners manual (but who reads them!!!) or as they say 'if all else fails, read the instructions'.  New plug can also help and check magneto gaps as Mark notes.  Now back to my watches !! 

:geek:

Link to comment
Share on other sites
Geo Distinguished Member

Geo

Posted
Posted

Good advice. I will definitely drain the tank when the season ends.

No need to Mark, you can always use this http://www.amazon.co.uk/Briggs-Stratton-Additive-Stabiliser-992381/dp/B003374F9E

Diesel is worse than petrol for going bad. It is easy to tell as it starts to smell like old turpentine that you left paint brushes in and forgot about.

Link to comment
Share on other sites
canthus Super WRT Addict

canthus

Posted
Posted

Good idea Geo to fill tank, but not sure addiive will help stop condensation if tank not full.  Main problem is carburettor bowl.  This will also suffer condensation but petrol will evaporate and leave water and residues, which just gets churned-up when the fuel is re-introduced. Residues can also block carb jets.  Normally an easy job to remove carb bowl and empty, worst will require new seal.  Electric mowers work first time,  :thumbsu:  !

Link to comment
Share on other sites
Geo Distinguished Member

Geo

Posted
Posted

Good idea Geo to fill tank, but not sure addiive will help stop condensation if tank not full. Main problem is carburettor bowl.

The additive is to stop the degradation of the fuel, not condensation. You are right about fuel in the carb being an issue, I always shut the fuel off and keep the motor running until the carb is empty. The residual heat in the engine evaporates what little petrol is left.

I have been doing this with my vintage bikes for years and have had no problems starting them after the winter lay up.

Link to comment
Share on other sites
clockboy Distinguished Member

clockboy

Posted
Posted

That's a museum item Geo, almost as old as me.

What my neighbour showed me is when the season is finished with all of his machines the tanks are emptied but then he runs the machines with what,s left in the carbs until they stop. He is a farmer so I guess he knows what he is talking about.

Link to comment
Share on other sites
Dpole Member

Dpole

Posted
Posted

Hi Mark, sounds like you had a bit of a problem starting your engine............ try starting a 915 honda that someone forgot to empty the fuel last winter, yes me....... what a plonker I was, 3 hours to strip and sort it out..... I think I would have liked to change a balance on a rolex, less time, but glad you got it all sorted..... :chainsaw:

 

Dave

Link to comment
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Restore formatting

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

×
 Share
Go to topic listing


  • Recently Browsing

    • No registered users viewing this page.

  • Topics

  • Posts

    • rjenkinsgb
      Accutron 218 transistors

      By rjenkinsgb · Posted

      Many would disagree: https://www.rohm.com/products/faq-search/faqId/234 https://uk.farnell.com/c/semiconductors-discretes/transistors/bipolar-transistors/pre-biased-digital-bipolar-transistors https://uk.rs-online.com/web/p/bipolar-transistors/8232832P?gb=s https://uk.rs-online.com/web/p/bipolar-transistors/0580240?gb=s (RS don't have a specific category, but over 1000 "digital transistor" items).  
    • Hawaiikook808
      Seitz Tool - Help determine if Seitz or not

      By Hawaiikook808 · Posted

      Thanks, ManSkirtBrew.  I started looking for a setup like yours and ran across this.  It was about half the price of the JKA Feintaster (depending on what auction you were in), and it's a Bergeon.  I bought it because I thought the price was fair (eBay - Buy it now), and I'm a sucker for vintage tools. It also has a table, so it should be easy to use for measuring jewels. I wonder if the the contact points can be changed out. Bergeon seems to manufacture new tables and accessories for the contemporary dial version. What do you guys think of it? I'm sorry this post seems to have taken a detour. I'm new here so let me know if I should start a new topic.
    • nevenbekriev
      Winding pinion making

      By nevenbekriev · Posted

      This is a flying cutter, usual one. The cutter itself is shown in the pictures in the first message, it is made of broken tungsten carbide drill bit. I asure that all the angles of the cutter are as they should be. I have video - little older one - that I made when onse making the same kind of winding pinion for a Poljot 2200, which is even smaller than this one. It is not easy to see in the video, but the tool rest moves about 1mm towards the object in Y direction and then returns back untill cutter is rotating. Then the spindle is rotated one tooth ahead and everything repeated untill all teeth are cut.
    • Trav2004
      Help Identifying movement

      By Trav2004 · Posted

      After a bit further research could it possibly be an AS 970?
    • Bonefixer
      FHF70 balance jewels settings

      By Bonefixer · Posted

      Latest project was a non-running ebay purchase with an FHF70 movement. I stripped and cleaned it, reassembled it, and got it running. So far so good, nothing damaged AFAIK.  I was oiling the top jewel on the balance (the one in the cock) which was a slightly unusual shock setting. I removed the spring (3 leaves) which was part of a chaton holding the cap jewel. This left the hole jewel behind which I retrieved with rodico and then lost it. I was taking it off the rodico, very gently as I thought, with tweezers, and then it just disappeared.  Fast forward a week, I got a donor movement, non-running, with the plan to just take the shock jewel that I’d lost. It was the same movement but had standard incabloc settings, and was steel rather than copper/brass.  I changed the cock and balance complete and it ran, not very well. I switched the lower jewel setting, cleaned and oiled both jewels and the replacement balance. Without the pallet fork the balance swings very nicely with a puff of air. With the fork in place, balance out, it flicks side to side nicely with power in the mainspring.  Put them together and it doesn’t run. The impulse jewel sits in the fork and it stops.      Any suggestions how I proceed? In case you didn’t follow that I have 2 FHF70 movements, nothing broken as far as I can tell, but mixing up the balance wheels and jewel settings results in a non runner. 
×
×
  • Create New...