Jump to content

Recommended Posts

Posted (edited)

Welcome to our forum.  I'm glad you found us.  Some of our veterans will likely step in soon.  One thing I know they will request is if you could please post some pictures; as close up and high-resolution as you can manage.  I should also ask if you have some good, fine-tipped tweezers?

Returning all the wheel pivots to their holes/bearings in the upper plate is, alas, an inherent and never ending struggle in this trade.  Some are easier than others.  Some will have you just getting one in as another comes out.  Some will turn your knuckles white as you take care not to break such slender pivots.  Having a difficult parts-movement to practice upon has helped me much.

Patience and practice will get you there.  Don't rush the Longines.  The brand is one of my favorites. 

Edited by KarlvonKoln
Clarity
Posted

If this is the first watch you have ever worked on, that's normal.

When I started, it could take me an hour to get the train bridge on. Sometimes I had to walk away and take a break, then come back later. You'll getter better at it eventually. 

Karl has given you good advice. Just remember to keep calm, have good lighting and magnification. Apply light finger pressure on the train bridge. You'll be able to feel a click whenever a pivot falls into a hole. Start with the biggest wheel first and work your way to the escape wheel.

Sometimes I have to put the screws in but only turn them a couple of rounds. Do not tighten them or the pivots will be damaged. This is to prevent the bridge from lifting and allowing all the pivots that you manage to get in to escape.

Fine tweezers is a must. But sometimes I use an oiler to nudge the pivots into the holes. 

That's all the tricks I have. The rest is practice and luck. And praying helps.

  • Like 1
Posted
7 hours ago, Chuck60 said:

I started working on this longines watch and I can’t seem to get the bridge back on the train of gears 

Just to remind that is considered polite to use the introduction section to introduce oneself. 

  • Like 2
Posted

It is polite to introduce yourself first. However fitting bridges on wheels takes practice and patience. The key in any horological work is don’t force anything in particular pivots they can be easily damaged. 

Posted
12 hours ago, Chuck60 said:

longines watch and I can’t seem to get the bridge back on the train of gears 

Always nice to help out to get an answer a model number as a company like longines Probably has made more than one watch. Then maybe even a picture would be helpful.

  • Like 1


  • Recently Browsing

    • No registered users viewing this page.
  • Topics

  • Posts

    • I have not attempted lume repair before but the idea is interesting. The uv glue might not bond directly with the old lume. I would probably mix the uv glue with a few drops of acetone before applying it to the old lume. The acetone would soften the old lume and allow the uv glue to diffuse into the surface and meld with it. Then allow a few minutes for the acetone to evaporate before curing it with uv. Most uv glues and varnishes have a layer of uncured resin that is caused by contact with oxygen in the air. This is the reason for the sticky surface after curing it with uv light. This uncured layer can be removed with IPA or by fully curing it by painting a layer of glycerin as the final layer to prevent contact with air, then curing it with uv.
    • Additional information for you,   Have a look at the watchfix courses by our administrator. Mark Lovick for a little more in depth training. Watch_tools_tipps.pdf TZIllustratedGlossary.pdf
    • The key is to try and find what the movement is and if there are no other numbers or markings on the movement then the next step would be using the like of BestFit based on the size and keyless works. The top one below is a Normal Bridle with no kind of end termination. What does the existing end termination look like.
    • Daniel, I guess You actually asked if the accuracy of the watch was improved after jewels added. One would not expect such accuracy improvement. The watch accuracy depends on many things and most of them are related to the balance and escapement. Well, it depends what is considered to be a no jeweled watch. If this is pin pallet watch wit cone balance pivots, then, believe me, replacing balance staff with one with cylindrical pivots in jewels will only worsen the things. Cone shaped pivots in cup bearings actually work better than  cylindrical, the only problem is that they wear faster. And, it will be hard to impossible to replace the pallet pins with ruby pins... The watch accuracy depends maimly on the balance and escapement adjustments ad it is no related to the presence of jewels. Adding jewels to the train wheel bearings may only lead to some amplitude increasing, and it is not sure too.  
    • Thank you so much! I'll experiment a bit with the UV glue and chalk and maybe eventually try to fill the hole.  I'll report back!  
×
×
  • Create New...