Jump to content

Recommended Posts

Posted

Depending upon where you are The British Horological Institute will have a list of accredited repairers or The American watch and collectors institute  AWCCI will be able to furnish you with a list in the states.  hope that helps.

Posted
30 minutes ago, wi33ard said:

is there somewhere other than seiko where i can get this item serviced/repaired? thank you

Of course there are independent watch repairers, however be aware that if for example the value of your Vintage Seiko is 100 (USD EUR, GBP,?you didn't event mentioned where are you located), a typical repair / service bill can easily be 200. 

  • Like 1
Posted

Lots of places. If you tell us more about yourself (clue: introduce yourself) and describe your watch, someone Here will be able to help. If you are really a Wizzard, I also wish it could be Christmas every day.

  • Like 1
Posted
2 hours ago, Klassiker said:

Lots of places. If you tell us more about yourself (clue: introduce yourself) and describe your watch, someone Here will be able to help. If you are really a Wizzard, I also wish it could be Christmas every day.

If he was a real Wizzard his watch would be working.

 

  • Like 2
Posted
14 hours ago, jdm said:

Of course there are independent watch repairers, however be aware that if for example the value of your Vintage Seiko is 100 (USD EUR, GBP,?you didn't event mentioned where are you located), a typical repair / service bill can easily be 200. 

i am in london. the watch has a serial stamped on the rear which reads 805958.what is strange about this watch is that where it might normally say water resistant, this is water proof

14 hours ago, jdm said:

Of course there are independent watch repairers, however be aware that if for example the value of your Vintage Seiko is 100 (USD EUR, GBP,?you didn't event mentioned where are you located), a typical repair / service bill can easily be 200. 

 

10 hours ago, markr said:

If he was a real Wizzard his watch would be working.

i was a real wi33ard, i would not need a watch

 

Posted (edited)
2 hours ago, wi33ard said:

what is strange about this watch is that where it might normally say water resistant, this is water proof

Seiko marked their warchtes water proof until about the end of 1970, and started marking them water resistant since 1969. So yours should probably be a 1970 watch, as its reference indicates (80 = August 1970/80/90...)

This is from 1969

EDIT: Philipk5 in the post below is correct, 80 means October 1968, not August 1970.

7005-8040-back-1969.jpg

Edited by aac58
Posted
42 minutes ago, wi33ard said:

i am in london. the watch has a serial stamped on the rear which reads 805958.what is strange about this watch is that where it might normally say water resistant, this is water proof

 

 

There should be some more numbers/letters on the caseback which should help identify the movement.

The use of the words "water proof" was replaced with "water resistant" some time ago (1969ish) by Seiko.

The serial number quoted indicates the watch was made in October of a year ending in 8 (ie 1968, 1978, 1988etc.

Hope this is useful and helps.

(I am pleased with myself for regarding who could do repairs not saying .......Roy Wood!) 

Posted
55 minutes ago, philipk5 said:

The serial number quoted indicates the watch was made in October of a year ending in 8 (ie 1968, 1978, 1988etc.

That's right, I mistakenly swapped the meaning of the numbers :Laugh:



  • Recently Browsing

    • No registered users viewing this page.
  • Topics

  • Posts

    • I would repeat what @nickelsilver says, and even more. I have at leas 10 old thread plates and I have never seen one that will cut like a normal die. I don't know if they are completely worn or have never been sharp enough, but I find them completely useless. And, for the new Indian ones, I have heard only bad things. For sure, if one tries to cut more thread on a winding stem, this hole of the plate is ruined. Further more, I have bad experience with all watch size thread dies that I could buy from the available machine  tool shops here. They could not cut normal thread even on brass rod. The size was significantly smaller and the pitch is like it should be for the claimed size... The thread shape was bad too. I will explain how I do threads. I use lathe that can cut threads and thus I can prepare perfect taps. I use milling attachment instead cutter in the tool post and so I can cut thread even on hardened rod. But I prefer to harden the rod after thread cutting and temper it only to light color change as to have the maximum hardness. Then I make a tap out of it by grinding. I prepare my dies for screw thread cutting with the taps I have prepared as described. In watchmaking, dies exist and are often used that are not cutting, but rather forming the thread. They are like nuts and don't have cutting holes and edges. This kind of dies I prepare and use. You will need soft steel plate , drill a hole in it, then cut thread, then make chamfer on one side, repeat the thread, harden. You can temper just a little or leave untempered, depending of the steel You use. Using such die is with soft steel rod (or completely annealed). Good oil is to be generously applied. The rod has to be with smaller diam than the thread size (about 0.8 - 0.9 x ), the diam is better determined by tries. The rod elongates by the thread forming too. When I have to make screws from harder material like SS, I just cut them on the lathe. You screw needs hardening and tempering to be finished as real screw.  
    • You could make a guide/jig. Cut a slot in a piece of metal approx the same thickness as the screw head, then drill a hole (screw head diameter) in that slot.
    • Tried a SR920W and its completely dead after 3 weeks 🤷‍♂️ 
    • Thanks so much for quick replies. I got some watch repair tools ordered, and will get back with pictures once I removed the back lid and get into it 🙂
    • Welcome to the WRT forum. 
×
×
  • Create New...