Jump to content

Can't get the movement out - Zodiac Hermetic


Recommended Posts

Hi  That back looks to me as though it can be removed. look round the perimiter for an indent for inserting a case knife if none visible you may need a case crab like the one attached as some of these cases are tight.    can you post close ups of the case edges it may help.

case back tool.jpg

  • Thanks 1
Link to comment
Share on other sites

In most cases one would find the slot to open a snap back case approximately 180 degrees from the stem.
The reson for this is to avoid the winding crown and case lugs beeing in the way, if it been serviced the slot might have moved in position due to a lazy watch repairer.
Then there is these "tight" snapbacks like Tissot and other uses then a tool like shown above will work.

Slot.jpg.3cf72728c905473c3545cbd9e3ad91b8.jpg

  • Like 1
Link to comment
Share on other sites

On 7/11/2020 at 12:06 PM, MrBeam said:

Any ideas?

In the thread below I posted about "Seiko style openers". That is what one wants in most cases.

 

On 7/11/2020 at 1:56 PM, watchweasol said:

you may need a case crab like the one attached as some of these cases are tight.   

I believe the tool  you posted is meant to be a bezel remover, with the flat side of the blates being on the case side once the watch is placed upside down. Otherwise two blade would be always in the way of the lugs or band. Some examples in the thread above.

  • Like 1
Link to comment
Share on other sites

Safety razors works for removing both the tight and not so tight snapbacks. if it turned out to be one of tight fit you would need a tool to press it back on, regulare types can be pressed on by just hand.

Link to comment
Share on other sites

4 minutes ago, Nucejoe said:

Safety razors works for removing both the tight and not so tight snapbacks. 

You think so? Hope you'll never need to get off a really tight, contemporary Swiss "tight case back" using only a razor blade, as you would end with a broken blade, or worse.

Link to comment
Share on other sites

7 minutes ago, jdm said:

You think so? Hope you'll never need to get off a really tight, contemporary Swiss "tight case back" using only a razor blade, as you would end with a broken blade, or worse.

I guess I am talented, never broke one. :P

Link to comment
Share on other sites

4 minutes ago, Nucejoe said:

I guess I am talented, never broke one. :P

I don't think so, a razor blade does not have the shear resistance to lift the many kilograms. It's made to cut, not to pry. Just make sure to wear anti cut gloves when experimenting that branch or metallurgy. 

Link to comment
Share on other sites



  • Recently Browsing

    • No registered users viewing this page.
  • Topics

  • Posts

    • Snap! I recently finished my Gruen 510 movement - though the case for mine is in a rather sad state; I'm going to try re-plating it (in nickel, it's not a gold one).   Re. the screws, I got a few of the one gram mixed batches from ebay. I've only needed a couple of screws for things so far, both rare, minuscule types - but both in the mix, after enough time sorting through them! The ones such as normal bridge screws are quite common in those lots.  
    • Two pins or screwdrivers angled out slightly, pressing through from the barrel centre from the opposite side so they contact just clear of the hole in the lid? eg. Strap pin driver needles or similar.
    • That's a good idea - shrinking down the nut and wrench size from the old casebook trick!
    • I missed this earlier. The dial isn't going into the holder, it should sit proud of it. This is what I am currently using which I print for each different movement.    
    • I didn't think pulling to set position would work harden the spring, in that position it is stressed where the arm starts. By work hardening i meant rapid polishing at that point, a bit like polishing a pivot work hardens as it compresses the steel. I doubt polishing by hand would achieve much in that respect though. Its finished, arm polished up mostly at the join to the bridge's main body. I'm ok with it, the screw holes aren't great as i had to open them up by redrilling and positioning it was difficult, I'm not much use with a loupe, opening up with a file might be a better option for me or i could just use the correct drill size 😅. And the detent is way too deep, i had to guess that with the stem release out of position and sat on top, but i only took one measure and went for it, no slowly slowly catch your monkey 😅. First go I'm happy , well sort of, it works and thats a big thing for me, next one will have a bit more finesse.  Anyone thats interested, after filing, i used a 2000 grade home made diamond  micro file and then 20 micron film, the film is much better than wet and dry, more stable to use and doesn't shed cheap grade grit everywhere , then auto polish on a sponge pad.
×
×
  • Create New...