Jump to content

Recommended Posts

Posted

Since I just got a circa an early 1990s Longines VHP I've started tracking it to the image of a clock on the NIST Atomic clock site.  I was shocked to see my watch had lost and gained few seconds over 5 days. So today I compared it again and it was -2.74 s. Then I looked more closely at the NIST numerical clock and  image of the clock below it.  They were different, and the clock image was -2.74 and stated "your device's clock is off by 2.74 s". I never imagined the clock image was representing my varying computer clock. Bottom line it it was a relief to learn my watch is right on time and my computer clock varies. Thought I would post this in case others are looking at NIST clock like I did.

\

Henryr

Posted

I often wonder just how precise time needs to be,I have around 80 watches, and thirty clocks and can say that the old adage is very true if you own a clock you know the time if you own more than one you are never quite sure :fpc:

  • Like 2
Posted

I was very surprised about the computer and I've noticed, when watching the news on TV the clock, usually shown in the lower right, is also wrong by a few seconds. Live and learn.

Posted (edited)

Inaccurate time on PC is due to poor OS implementation which uses a single time server, often also inexact like time.windows.com. Below an article on how to change this setting to a better one, like e.g. uk.pool.ntp.org if you're in the UK, or replace uk with your country code. Doing that I have about 0.3 sec difference with the NIST web page, and that is very normal because of the delay between said USA server and a PC in e.g. Europe.

https://answers.microsoft.com/en-us/windows/forum/windows_10-other_settings/how-to-force-windows-10-time-to-synch-with-a-time/20f3b546-af38-42fb-a2d0-d4df13cc8f43

Edited by jdm
Posted

This is very evident when trying to purchase from eBay. You're down to the last few seconds and you place a bid at the last 2 seconds and 5 others bid and you miss out. Turns out there were a couple extra seconds because your computer time and the time on the eBay servers was different. Annoying!

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Restore formatting

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

  • Recently Browsing

    • No registered users viewing this page.
  • Topics

  • Posts

    • Thanks for this post MikePilk, I just came across a similar problem with an Omega 1022.  The problem I had was the seconds pinion spring was bent out of shape and did not even engage with the wheel properly, so the seconds hand was not moving at all. (no power loss though :) I removed the automatic module so I could access the spring and work on it. Once I bent it back close to the right shape, I experienced the same problem you reported about power loss.  Many tweaks later, and the seconds hand is moving properly again, with amplitude back to good numbers again. Cheers
    • After cleaning up the pivots, I made bushes on the lathe. At this point I've pressed in 6 bushes (3 sets) and the wheels turn smooth. What I can also tell you, is that I'm not looking forward to final assembly. Getting the pivots aligned seems to get exponentially more difficult with each wheel that is added.
    • Islands are interesting places to live depending upon their size and other factors. This is a bigger island and it has a bridge to get there at least on one end. It's also big enough that you don't have to go someplace else to get things typically. It can be a problem if you get a job in Seattle though. Yes I've known of people who commuted from the island to Seattle for a job and I don't quite remember how many hours it took but it took a long time. So basically islands are nice if you don't have to leave very often.
    • Thanks @JohnR725! Everything you say makes a lot of sense and is encouraging to read.
    • isn't it nice to have a decent case open or when the case doesn't want to be opened? In the case of a Rolex watch that supposed to pass specific water resistant testing you probably do need to tighten the back down. But they shouldn't be tightened so much that they risk stripping the threads out. Then the other problem that comes up is the gaskets can start to disintegrate and then getting the back off can be quite a challenge unless you have a really good tool and perhaps some penetrating oil to loosen things up. Yes really nice case marking. When I was in school we were taught to mark the cases and  the American watch and clockmakers Institute even had a? So if you joined at one time they would give you an identification number. They were explaining or giving an example of if the watches ever found in you have a unique number they can perhaps figure out the history of the watch or identify the body it's attached to for instance not that that probably comes up that often. So you got a unique number and even made a special metal stamp that you can purchase. It wasn't a super big aggressive stamp but still it left a mark in the back of the case. Then I heard from people at work on Rolex watches they were using a felt pen indelible but later on they decided that was bad because apparently the ink could release  chemicals although it seems like once it's dry that shouldn't be an issue. Then of course today was nice is you can keep computer records sealed have to mark anything at all I personally find it's best to leave no reference behind that you were even there. Especially when you have a beautiful watch that has no markings at all and now it has your scribbling all over it not good typically if there is a typical and watch repair?  a lot of minor repairs you don't need to do a complete servicing. But beyond a certain point you're going to have to take apart a lot of stuff you're going to disrupt the lubrication even if it looks perfect right now and yes you might as well just go ahead the service the whole thing. also in a watch like this where a lot of things seem to be going on the complete service would be better then you'll know exactly where you stand versus dealing with unknown mysteries for prior repair.
×
×
  • Create New...