Jump to content

Seiko 5 6319-7010 repair


TSGarp

Recommended Posts

Hi,

I've found my old Seiko 5 and it's looking a bit dishevelled.

I've had it from new in the 70s and it's been sitting in a draw for the past 30 years.

I need the strap replaced, glass, either with the original style or normal? and to get rid of some of the scratches on the body.

Can anyone tell me the best place to go to please. I'm in the Manchester area of the UK.

Thank you

IMG_2019.jpg

Link to comment
Share on other sites

43 minutes ago, TSGarp said:

 Is this a usual thing or is it rare that it was done for this model?

It's very usual. All Seiko mechanical have a 2nd language, Spanish is the most common, followed by Arabic.

You should check the watch on a timegrapher or equivalent application. Even if servicing professionally would cost times its value, at least you would know its "health".

FYI that we have a dedicated section for general watch talk like this subject, as well one for new members to introduce themselves.

Edited by jdm
Link to comment
Share on other sites

Hi, I have a pair of these watches, you can buy the proper faceted crystal/glass on eBay but at £34.00 if I remember rightly. I have one with the correct crystal and one with a plain replacement glass, good luck in getting it sorted.

IMG_20170213_173053.jpg

  • Thanks 1
Link to comment
Share on other sites

Hi  If you are looking to do it yourself Then cousins uk is the place to start for bits. If you are looking for a repair agent Then go to the British Horological Institutes wab site and look up the list of accredited repair agents that way you are assured of a quality repair.

Link to comment
Share on other sites

Hi I Ts,  it isn't that rare but still a nice watch on the wrist, and the 1st watch I disassemble, cleaned and oiled, and reassembled that worked lol. Sometimes they pop up on eBay for about 60quid ish. You need a 16mm strap for it. 

Link to comment
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Restore formatting

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.



  • Recently Browsing

    • No registered users viewing this page.
  • Topics

  • Posts

    • All I do is use a fine marker (sharpie) to put the service date on the back cover, this way it can be removed with some IPA and does no permanent damage to the watch. I'm in two minds about the whole service marking thing, sometimes it's good/bad to see the markings on the watch case back as you know it's been worked on and vice versa. However, if I took my car in for a service and the mechanic scratched some code into the housing of my engine I wouldn't be too impressed. Hence, I think my sharpie solution is a reasonable compromise.
    • hmmmm.... maybe there is a way to skin that cat 🙀 let me think on it... unless anyone else has any ideas? I left the opening in the side of the base and ring quite large to maybe allow you to grip the crown, but appreciate this may not always be possible, especially for small movements where the crown will not extend past the outer wall of the holder. I noticed this also, but after using the holder for a while I noticed that the ring/holder began to wear into shape (rough edges/bumps worn off) and the size became closer to the desired movement OD. Maybe with some trial and error we could add 0.5 mm (??) to the movement OD to allow for this initial bedding-in?
    • Hi nickelsilver, thanks for the great explanation and the links! I'll take a good look in the article.  Especially this is great news to hear! Looking through forums and youtube videos I was informed to 'fist find a case and then fit a movement for it'. But seems that's not the case for pocket watches at least?  I guess I should be looking to find some 'male square bench keys' for now. I was thinking of winding the mainspring using a screwdriver directly, but I found a thread that you've replied on, saying that it could damage the spring. 
    • Murks, The rate and amplitude look OK, and the amplitude should improve once the oils you have used get a chance to move bed-in, also I notice that you are using default 52 degrees for the lift angle, if you get the real lift angle (assuming it's not actually 52) this will change your amplitude - maybe higher, maybe lower. I notice that the beat error is a little high, but not crazy high. At the risk of upsetting the purists, if the balance has an adjustment arm I would go ahead and try and get this <0.3 ms, but if it does not have an adjustable arm then I would probably leave well alone. Just my opinion.
    • Hi everyone on my timegrapher it showing this do a make anymore adjustment someone let me know ?    
×
×
  • Create New...