Jump to content

Air purifier


jdm

Recommended Posts

When looking at how quickly dust accumulates, or at the particles in strong sun light, I began thinking that when working with watches clean air must be better. So got myself one of these, it's quiet and I like the look. Affordable at €30 from Amazon. Do you use one?

51fLu0I8s4L._SL500_AC_SS350_.jpg

Link to comment
Share on other sites

I've got one - a purifier, not a dehumidifier - but I have to admit I have hardly used it. I don't have a dedicated room, so it's hard to keep really clean. We and the dog are in and out all the time, bringing in new dust, clothing fibres and hairs. I would need to run it all day to keep the air clean all the time, and as I am usually only at the bench weekends that would be extravagant. I don't want the machine running near me when I'm working because of the draught, so a sensible option would be to run it for an hour before I start work. I will try to get into the routine of doing this, as my main problem is contamination.

Link to comment
Share on other sites

Looks nice :)

I have to run a dehumidifier 24/7 here, due to a tropical climate otherwise slowly destroying everything. My workshop-room is sealed in every spot I can think of, but there is still dust ingress, and after a few months there is a layer of it all over the floor (and worse, my bench).

The dehumidifier has a filter that slowly gets dirty, but I think it only captures a fraction of the dust in the air. I've thought about getting some sort of purifier that uses static electricity to capture dust, and see if that makes a difference..

Link to comment
Share on other sites

If you are in an uncarpeted room (most working on watches would want to be!) you will find that adding a small carpet away from the bench helps with dust surprisingly well. At one place I worked there was an about 2.5 meter long removable carpet in the hall outside the clean workshop; the boss decided it must go, "it's a dust magnet!!"... well, it was- immediately our benches were dustier. Put it back and it was 10x better. I experienced the same in a workshop I had for a while which had a tight weave industrial carpet; at first I hated it (and couldn't change it), then I realized after several months that nothing, anywhere had dust on it

  • Like 3
Link to comment
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Restore formatting

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.



  • Recently Browsing

    • No registered users viewing this page.
  • Topics

  • Posts

    • Yeah, I saw that in the tech sheet but I don't see how it can be adequately cleaned with the friction pinion still in place. I've accidentally pulled the arbor right out of the wheel once when I used a presto tool to try and remove it. Mark shows how he does it with the Platax tool. Those are a little too pricey for me so I got one of these from Aliexpress and I just push down on the arbor with the end of my brass tweezers. That usually gets it most of the way out and then I just grab the wheel with one hand the and the friction pinion with the other and gently rotate them until it pops off. Probably not the best way but it's seemed to work for me so far.    
    • Thanks, Jon Sounds like a plan. Obviously I'll have the face on so do you think gripping with the holder will create any problems, but I will check in the morning to see how feasible it is but I assume it only needs to be lightly held. As for holding the movement instead of the holder won't be possible in this scenario as one hand will be puling on the stem while the other pushes the spring down. That was my initial concern is how the hell can I do this with only one pair of hands. All the other times I've had to remove the stem hasn't been a problem, apart from the force required to release the stem from the setting lever, but now I need to fit the face and hands its sent me into panic mode. If it had the screw type release things would be a lot simpler but that's life 😀       
    • Hi Jon, do You think that relation spring torque - amplitude is linear? I would rather guess that the amplitude should be proportional to the square of the torque. I had once idea to check it, but still haven't.
    • I did not. I thought about it, but I had cleaned it in my ultrasonic, and the tech sheet shows lubricating it in place already assembled, so I figured discretion was the better part of valor. Although since I have to depth the jewels anyway, maybe I pull the pinion off to rule it out 100% as part of the problem. Do you know if there's a safe way to do it? I don't want to use a puller because it would push down on the plane of the wheel, and that seems like a Bad Idea. I thought about using a roller table remover, but I don't think I have a hole stake pointy enough to push it down.
    • Before putting it back in the case I would fit the hands and use a pin vice on the stem to make sure the hands were in line. 
×
×
  • Create New...