Jump to content

Question About Old Watchmakers Desk


jdrichard

Recommended Posts

I was asked by the curator of the Canadian Clockmakers Museum what the small pocket on the lower right side of the desk is used for. It is next the the small poster and bottom right part of the desk, just below the desk top and about 3 inches wide by 6 inches tall.7d72dfd66397c90260c86bbe01df29e8.jpg

 

 

Sent from my iPhone using Tapatalk Pro

Link to comment
Share on other sites


I will look this up. What specifically did they use it for?


Sent from my iPhone using Tapatalk Pro
They would load a bristle brush with it and brush down the parts. Sounds crazy I know, but that was part of good cleaning procedure 120 something years ago.

Goodrich's book The Watchmaker's Lathe its Use and Abuse has and illustration describing the chalk hole.
  • Like 1
Link to comment
Share on other sites

They would load a bristle brush with it and brush down the parts. Sounds crazy I know, but that was part of good cleaning procedure 120 something years ago.

Goodrich's book The Watchmaker's Lathe its Use and Abuse has and illustration describing the chalk hole.

Thanks. I have that book and will look this up

Sent from my GT-N5110 using Tapatalk

Link to comment
Share on other sites

13 hours ago, jdrichard said:


It’s just a square opening in the desk???


Sent from my iPhone using Tapatalk Pro

    i was looking at something else on the bench top !!!      put a circle around something on the bench top,   i'll try again - vin

Link to comment
Share on other sites

For those who are curious, French chalk is basically magnesium silicate, talc. It's the lowest number on the Mohs scale for minerals.

 

Another mineral traditionally used in watchmaking is Spanish powder, or blanc de meudon or blanc d'espagne. This is calcium carbonate (primarily), slightly more aggressive as an abrasive. On a watch with gilded plates and bridges, when they are tarnished/stained and unaffected by normal cleaning methods, this stuff can be rubbed on wet with fingers or brush. It does an amazing job of brightening the parts, without leaving a scratch. Calcium carbonate is the main component of blackboard chalk, so if your local drugstore doesn't have it* crush some up and give it a try.

 

 

*we're really spoiled in my area with a drugstore thathas all kinds of cool stuff. Just got silver nitrate there for a new batch of dial silvering powder.

 

 

Link to comment
Share on other sites

For those who are curious, French chalk is basically magnesium silicate, talc. It's the lowest number on the Mohs scale for minerals.
 
Another mineral traditionally used in watchmaking is Spanish powder, or blanc de meudon or blanc d'espagne. This is calcium carbonate (primarily), slightly more aggressive as an abrasive. On a watch with gilded plates and bridges, when they are tarnished/stained and unaffected by normal cleaning methods, this stuff can be rubbed on wet with fingers or brush. It does an amazing job of brightening the parts, without leaving a scratch. Calcium carbonate is the main component of blackboard chalk, so if your local drugstore doesn't have it* crush some up and give it a try.
 
 
*we're really spoiled in my area with a drugstore thathas all kinds of cool stuff. Just got silver nitrate there for a new batch of dial silvering powder.
 
 

Again, thanks very much. I will pass this info along to the curator of the clock museum.


Sent from my iPhone using Tapatalk Pro
Link to comment
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Restore formatting

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.



  • Recently Browsing

    • No registered users viewing this page.
  • Topics

  • Posts

    • I have two Seitz sets, one ancient (with the 3mm anvils) and one just old (with 4mm anvils) plus a collection of spare pushers of assorted vintage. Not one of them is marked with it's size. Something which I have found very irritating when I have been using the tool and not returning pushers to their correct place in the tray every time as it means that I have to get the calipers out and measure them. These were bought as sets and collectively I have over 100 pushers so it would seem highly unlikely (if not inconceivable) that they are all cheap knock offs, especially as they are old enough to pre-date the prevalence of the Chinese knock off industry (at least as applied to watch making tools). I therefore believe them to be original Seitz parts. And there is no numbering. The shape of the bottom of the pump pushers is the same as your photo. The only thing that may not be the same is that the slotted insert (looks like a screw but is in fact a bayonet) should be brass. Yours looks the same colour as the steel but that could just be the lighting.
    • The original database is available on iOS devices here: https://apps.apple.com/fi/app/ranfft-watch-movements-archive/id6502008939
    • I no longer have my set so I can't help anymore sorry. Many on here have the set as its a must have tool for watch making/ repair.
    • It needs to be stirred before use and that makes it feel a lot thinner than when in the bottle. Does it feel as thin as 9010 after stirring it? I guess not! Yes, it's strange! I don't know, but if it is on impact it would make sense.
    • Thanks, OH! I agree with you. I'm currently looking at them under magnification, and they are consistent in shape and form for each section (flat pushers, pump pushers, concave, reamers, etc.). Though, a few are in bad condition and need to be replaced.  Before I cancel the return I have already initiated on eBay, can any of our members check to see if there are inconsistencies in markings on their sets? Also, I have included a snapshot of the bottom of one of the pump pushers, which are very unique in shape.  Can someone tell me if the bottoms of their pump pushers match this photo?  I'm hoping that Seitz had some inconsistencies in manufacturing over the years regarding markings.  Crossing my fingers. I appreciate you guys. Frank
×
×
  • Create New...