Jump to content

Recommended Posts

Posted

GLAD TO BE HERE NEED SOME EDUCATED HELP ON A ETERNA MILITARY THE SERIAL NUMBER DATES THE WATCH 1942.THE MOVEMENT LOOKS ALMOST LIKE A 852S BUT FROM WHAT I HAVE READ THE 850,852 AND THE 852S WERE ALL 15 JEWEL.MY WATCH HAS A POLISHED SURFACE 17 JEWEL CENTER SWEEP WITH SLIGHT VISUAL DIFFERENCES FROM THE 852S .NOW I DID READ THAT ETERNA MADE ETA'S 853 THROUGH 859 AND THERE IS NO DOCUMENTATION ON ANY OF THOSE.AND THE LAST THING IS THE HOUR HAND HAS 2 DOTS FROM WHAT I HAVE READ THEY COULD HAVE BEEN USED AS A PILOT WATCH .I HAVE RESEARCHED THIS FOR A LONG TIME AND HAVE NOT SEEN ANOTHER ONE FROM ETERNA OR ANY DOCUMENTATION ANY HELP WOULD BE GREAT THANK YOU AND GLAD TO BE HERE.

best watch 2.jpg

best watch.jpg

Posted

Most military watches have a number engraved on it somewhere... there always remained the property of the military and the numbers were meant to keep track of who was issued what. Also the numbers helped to ensure servicing records kept accurately.

For the two dots on the hand.. this was more to break up the large mass of luminous material.. nothing special here.

Also I believe most military watches are usually black dialed?

Anilv

Posted

thanks for your input but your wrong on several levels about black dials and white dials and what eterna made and did not make  your input is nothing special.A few Eterna ATP watches have been found with both black and white dials, mostly black, and a central seconds sweep hand.    Black dials and central seconds are inconsistent with the ATP characteristics, but a handful of Eterna ATP watches exist and it is thought that about 600 may have been made from the known serial numbers.So there are black and white dials and the 850 series movements

3-atp-elgin-the-watch-on-strap.jpg

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Restore formatting

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

  • Recently Browsing

    • No registered users viewing this page.
  • Topics

  • Posts

    • Get well soon Old Hippy, torn muscles.,  not good
    • Id love to see how he has the output shaft mounted to this setup, as I have the same rotary stage and stepper in my build.
    • If you see at least one thread protruding, or even a half, then you may have a chance using this "tool", but don't squeeze hard. Lot's of patience, and if you notice any signs of loctite or other adhesives, then apply several drops of acetone on top of broken stem. Use heat (hair dryer) also. You should be able gradually turn it counterclockwise, just like i did on this broken Timex stem, which was glued with something like nail hardener. Then you can use an extender to save your broken stem. https://m.media-amazon.com/images/I/513DVvkfW5L.__AC_SX300_SY300_QL70_ML2_.jpg   You can also try cutting a small grove / slot on top of the broken stem to use 0.7mm flat screwdriver.   Depending on the Crown material and Stem material, you can try dissolving the stem. 
    • How long had it been without any wind before you first put it on the timegrapher?  Perhaps there was some debris / old lubricant that loosened up while you were waiting to do the 24 hour reading? I recently serviced a Seiko 6319 that immediately after service was absolutely horrible on the timegrapher - 24 hours later (without me doing anything) it was rock solid!  I was a little surprised by this (as I have seen improvements in amplitude after letting it run in but never a watch going from useless to great!). I was suspicious that some dirt must still be in there so I took it apart and cleaned and lubcricated it again and had exactly the same experience - snow storm that after some hours turned into a nice straigh line with good amplitude 🤷‍♂️
    • Yes, I know it was able to run before just enough that everything supposed to be affixed with shellac could fall out. I won't get back to work on this watch for several days at least, but one thing you mentioned about the banking pin adjustments being intended for fork horn clearance got me wondering.... The last adjustment I made to the entry stone yesterday did not solve the problem when the balance is installed. The escape teeth can't quite clear the stone when the balance swings. But I thought it was going to work because manually snapping the fork back and forth did allow the escape wheel to advance almost all the time. I wonder if there's another issue with the impulse jewel, that I have to shellac again anyway. I am going to measure the fork slot and the jewel because I am curious if it is the right size or possibly narrower than it should be. My thinking is if the horn clearance is too great maybe it is not getting enough impulse to clear the escape tooth. But pushing the fork with a tool can move it far enough to clear the escape wheel tooth.  I'll see later in the week. I didn't expect a big challenge from this watch because it ticked for 5 minutes before stopping without shellac. As always I was way wrong.
×
×
  • Create New...