Jump to content

Hello from Germany

MrWatch

By MrWatch
in Introduce Yourself Here

 Share

Recommended Posts

MrWatch New Member

MrWatch

Posted
Posted

Hi, I'm 56 and live near Stuttgart.

I have been collecting pocket watches for a while now and own several watches in need of repair.

I'm mainly interested in vintage pocket watches, especially in such with fusee movement and English lever escapement.

I am a beginner in watch repairs and look forward to learn as much as I can.

Jens

DSC00775.jpg

Link to comment
Share on other sites
oldhippy Distinguished Member

oldhippy

Posted
Posted

Thank you for your introduction and welcome to this friendly forum.

Before starting on fusse pocket watches, they are very different from English Lever movements and much more difficult. The English Lever is best to start with, apart from the size they are very much like a basic watch movement.

Link to comment
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Restore formatting

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

×
 Share
Go to topic listing


  • Recently Browsing

    • No registered users viewing this page.

  • Topics

  • Posts

    • LittleWatchShop
      Balance cock stud screw

      By LittleWatchShop · Posted

      Either of those ideas might work. Did you try putting a thin layer of rodico on the cocktail and then push the screw through it. Afterwards, soak in one dip
    • Jon
      Part swapper to part maker

      By Jon · Posted

      I would use some binding wire around the part before heating it. It protects the steel from being burned. I know that sounds strange, as you're going to heat it with a blowtorch, but if a part is thin and delicate the steel can literally burn away before your eyes, which isn't funny if you've put hours into the job. I bought some tools steel from Cousins a few years ago which turned out not to be tool steel, because it couldn't be hardened or tempered. I wasn't impressed, as I had spent two hours making the part for it to be useless.
    • watchweasol
      Questions about my Bravingtons Renown Mantel Clock

      By watchweasol · Posted

      Hi that’s what was meant by animal glue “ a glue made from animal products”. Ie bone , skin and other animal residues.  There was a place at Huntington YORK who used to boil down the ingredients. It stunk.   We used it in pellet form in a sort of Bain Marie on a gas ring  it was very good, didn’t think it was around any more with the modern glues, 
    • Zedster
      Balance cock stud screw

      By Zedster · Posted

      It's back to the drawing board I'm afraid. As pointed out, the Rodico trick is so fiddly and my pin vice jaws don't close in union. I tried but the screw is so small it's hard to grip the screw in the Rodico without it moving all over the place while trying to get it in the vice. I started to shake too much so gave up before the screw flew off somewhere never to be found again.  I'm now thinking that maybe I could bond the screw on the end of a bit of peg wood and then dissolve the adhesive afterward.  I just had another thought🤔 I have some really small PCB drill bits maybe I could drill a small hole in peg wood and push the screw in, as stated I only need to get the screw started.  Another idea 🤣 Magnetize the screwdriver to hold the screw 🤔 
    • Chief
      Generic screws for unknown movements

      By Chief · Posted

      Yeah there is a spring under there. Hopefully now I can source a screw for the click and the bridges! Thanks for your help!
×
×
  • Create New...