Jump to content

Hello From Germany

Klassiker

By Klassiker
in Introduce Yourself Here

 Share

Recommended Posts

Klassiker Distinguished Member

Klassiker

Posted
Posted

New member, first post on this forum.

I'm British, but currently living and working in Germany. The interest in watches has probably been a lifelong thing really, but more of a passing interest until a few years ago. My job is related to merchandising, including watches, and I started reading the watch blogs and forums on the internet for information. Then I went on business to Baselworld, and in my own time to Munichtime. There I got into contact with the DGC (German Chronometry Society), which is a club organising watchmaking seminars for hobbyists. Now I've got my own little workshop and boxes full of scrap watches!

The ones I bought to wear and not to dismantle are a Junkers Bauhaus 6050-5, a Seiko SARB017 and a 2nd. hand Nomos Orion. My ambition is to get competent enough to do the routine servicing on these, but that's a long way off yet!

Link to comment
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Restore formatting

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

×
 Share
Go to topic listing


  • Recently Browsing

    • No registered users viewing this page.

  • Topics

  • Posts

    • noirrac1j
      Rolex 2235 escape wheel jewel setting replacement

      By noirrac1j · Posted

      Hell0 @nevenbekriev. Thank you for your advice. I have removed the old setting using my staking set--I will keep the KIF spring, since it is still good.  I am awaiting the replacement setting, and will update when I do that. In the mean time, I looked at the escape wheel and it looks ok. What do you think?    
    • Hawaiikook808
      Seitz Tool - Help determine if Seitz or not

      By Hawaiikook808 · Posted

      Aloha All, I recently bought this Seitz tool on eBay, but it is missing some pushers reamers.  I ended up ordering new parts for those that were missing before I received the actual Seitz tool (bad idea).   Upon inspecting the pushers/bits, I noticed 23 of the 56 provided with the set had no numbers. Further inspection revealed a huge difference in the quality of those unnumbered.  Do all Seitz pushers/bits have a number on them?  I'm pretty sure that 33 of the 56 I received are cheap Chinese knockoffs.  The worst part is that I ordered $80 of parts to replace the missing pushers/bits, and now I'm looking to return the tool. I'm not crazy, right? If these are Seitz parts, they should all be numbered, correct? The first two pictures are the Seitz (numbered), and the other pictures are the suspect parts.  Will I even be able to get a refund?  Thanks, Frank     
    • luiazazrambo
      WWW Eterna sucked me in.

      By luiazazrambo · Posted

      It was £10 + min fee, total £16, could not leave it there. Its a Stanton A.D.2. http://stanton-instruments.co.uk/
    • Geotex
      Generic screws for unknown movements

      By Geotex · Posted

      Chief- The picture below shows the three parts from the dial side that are most useful to "fingerprint" a movement in conjunction with the diameter of the movement.  That's why forum participants are always asking for dial side photos in posts asking for identification.  As far as the setting lever screw, it actually sits loose in the main plate. The threads engage the setting lever below, and the elongated stem above the shoulder sticks through a hole in one of the bridge plates so that it's held captive if unscrewed all the way.  So you may be fine as far as that goes. 
    • Chief
      Generic screws for unknown movements

      By Chief · Posted

      So I found what I believe is the setting lever screw! Am I right in thinking the screw next to the click is the correct one for the setting lever? However if it is, it doesn't fit in the hole which I believe is for it! I can get the lever to sit nicely on the stem and line up with a hole, but the screw only goes as far as the shoulder and stops. It's as though the hole is too small! The dial side has been disassembled by the way, the other wheels are in my tray
×
×
  • Create New...