Jump to content

Omega Speedmaster Moon Watch Question

rattandsonwatchmakers
 Share

Recommended Posts

Mark Distinguished Member

Mark

Posted
Posted

I suggest a full service every 5 years wether there is evidence of a problem or not. 

 

Oil degrades and becomes less useful over time and it needs to be cleaned and renewed to reduce wear, just like with any mechanical item (a car being the most obvious)

 

:)

Link to comment
Share on other sites
WillFly Distinguished Member

WillFly

Posted
Posted (edited)

It's a bit like a car. You can run it and run it and not worry and the, one day - bam! the cam belt's gone and you're into a major spend. I think a basic clean and service after 10 years service wouldn't hurt, and will get rid of that oil drying round the jewels...

 

Hah - just cross-posted with you, Mark!

Edited by WillFly
  • Like 1
Link to comment
Share on other sites
bobm12 Distinguished Member

bobm12

Posted
Posted

Hi rattandson,

 

I would service it in order to avoid a failure! Being an Omega, you can either send it to the factory or do it yourself/professional. The whole point is doing it properly and avoid, as previously said, a failure that might endanger other parts of the watch and make the service more involved (costly, time consuming, etc). I think service as preventive!

Link to comment
Share on other sites
noirrac1j Distinguished Member

noirrac1j

Posted
Posted (edited)

Rattandson your question seems to have a least two components. I'll handle both: 1) Does a gorgeous high-quality watch like an Omega moon watch deserve to be serviced after 10 years of working without fail? Yes it does ! 2) Would I do the service myself? Probably not because I have a fear that I will totaly mess up any of my Omegas--especially if they have complications. The moon watch is a chronograph....major complication.

 

JC

Edited by noirrac1j
Link to comment
Share on other sites
Ray WRT Addict

Ray

Posted
Posted

I recently got the very same watch and I will definitely be getting it serviced every 5 years to keep it in tip top condition. I'd wanted it for a very long time and never intend to sell it so want to look after it. That gives me 5 years to get good enough to service it myself or more likely give it to Mark!

Link to comment
Share on other sites
jnash Super WRT Addict

jnash

Posted
Posted

It's a bit like a car. You can run it and run it and not worry and the, one day - bam! the cam belt's gone and you're into a major spend. I think a basic clean and service after 10 years service wouldn't hurt, and will get rid of that oil drying round the jewels...

 

Hah - just cross-posted with you, Mark!

 

 

ahh the old car explanation when talking about servicing..... the most used and best example....

Link to comment
Share on other sites
WillFly Distinguished Member

WillFly

Posted
Posted

ahh the old car explanation when talking about servicing..... the most used and best example....

Yup - an old chestnut - but worth repeating.

 

I'm always amazed at the people who think a watch should be serviced for next-to-nothing - and then cheerfully shell out £200 every year for their car to be serviced. When you think of the potential wear and tear on a fully functional mechanical movement over, say five years...

Link to comment
Share on other sites
Mark Distinguished Member

Mark

Posted
Posted

It's the only thing people are most likely to service on a regular basis, so it's a natural illustration.

 

But we can talk about boilers if you want :) I had a new combi boiler fitted in my house five years ago - at the time all the rads and pipes were flushed and chemicals were added to clean the crap away.

 

I have not had it touched since and now just last month the hot water kept cutting out (painful mid-shower). If I had it serviced every year in accordance with the manufacturer guidelines would have escaped a lot of grief, agro from the wife and cold showers.

Link to comment
Share on other sites
 Share
Go to topic listing


  • Recently Browsing

    • No registered users viewing this page.

  • Topics

  • Posts

    • RichardHarris123
      First Project Already A Bit "Sideways"

      By RichardHarris123 · Posted

      Screws are available as below. 
    • ColinC
      First Project Already A Bit "Sideways"

      By ColinC · Posted

      Personally I would salvage the missing screws from some donor movement.  I also bought a random selection of screws "Assortment of Stainless Steel Watch Screws" for next to nothing.  As for using an Alum solution - I had great success with that removing a rusted stem from a stainless steel crown.  The best piece of advice I read on doing that was to keep the solution warm so that the reaction didn't take weeks!  I did it in a couple of hours with the solution in jam jar and the jam jar in a saucepan full of water which I left on an induction hob maintaining about 60C in the Alum solution.
    • DDean
      First Project Already A Bit "Sideways"

      By DDean · Posted

      I decided that it was time to tackle the piece that I'd set aside as my first project. The subject in question is a Gruen Veri-Thin pocket watch.  It winds and "runs".  On the time grapher, it has reasonable amplitude (240 or so depending on the position), but was loosing close to a minute a day.  The stem also has the annoying tendency to just come out when pulled, which makes it super hard to set the thing.  As with many things this one started sideways and just got more so.  I was able to overcome the mangled "tab" on the back case cover (a well placed, very sharp knife enabled me to get in when I couldn't get a purchase on the mangled tab with a case knife.)   I was then sort of shocked to find that one side of the dial was held down with some sort off tape or adhesive material as someone had broken the dial foot screw on that side and left the broken screw in the mail plate. The loose stem does in fact seem to have been a poorly tightened setting lever screw, but I'm afraid there may still be gremlins in the keyless works.  While I was able to get the stem to stay in by putting everything in the right place and tightening the setting lever screw (before I took it all apart for cleaning and inspection), it just didn't seem to all sit right. The final gremlin showed up when I was taking off the lower cap stones for the balance and escape wheel (yes the Gruen 380 seems to have a cape jewel on the escape wheel).  The balance stone came off fine (but that in fact is the smallest screw I've ever seen.  When I turned the movement around to get the one off the escape wheel setting, I found that the screw head had been mostly sheared off.  After some reading and looking at what I had, I decided to try and tease what was left of the screw out of the hole by nudging what was left with the corner of my smallest screwdriver.  After 20 minutes or so, I was able to get the remains of that screw out. The picture I'm including of the disassembled movement was taken before I got the second cap stone off, so in the picture, it's still attached to the main plate (for those looking carefully, you'll only see the one cap setting in the pic.) Now I'm left with: A broken dial screw inside the main plate that needs to come out A broken cap stone retention screw that I have in my parts tray, but that is strictly useless and needs to be replaced. The need to get another dial foot screw I'm contemplating solving the first problem by soaking the main plate in an alum solution.  I think the main plate is brass and shouldn't be affected, but I have not been able to confirm.  This seems like the easiest option as I can't really access both sides of the screw to use the pricey Bergeon tool (which I don't fancy buying unless I have to.) I have located a couple of donor movements and have questions out about whether or not the include the dial foot screw and prompting for pictures of the dial side so  evaluate the cap stone settings.  I've also found that a supplier in this country does have the cap stone settings, but isn't overly clear about whether the screws are included. Are these the types of things that one can scavenge out of assortments or is it best to just grab one of the donors assuming that they look like they have what I need?  
    • ColinC
      Need some crystal replacement advice

      By ColinC · Posted

      I visited this place last year just before they closed their counter service - amazing shop (filled from floor to ceiling!) and the guy that was working there was really knowledgeable and helpful!. Their website isn't as good as Cousins but I understand that if you fill out the contact form they have stuff that isn't on the site. https://gleave.london/mineral-flat-bottom-domed/
    • tomh207
      Standard crystals to replace tension ring crystals

      By tomh207 · Posted

      As always in this game the answer is “it depends “ because the first one worked out ok doesn’t mean all will. A case could be made in a way that it would not really matter much, sounds like your first example. However a case could also be made so that only a tension armoured crystal could be used. Generally you replace like for like to maintain the integrity of the watch.   Tom
×
×
  • Create New...