Jump to content

zodiac not ticking

Sanders

By Sanders
in Watch Repairs Help & Advice

 Share

Recommended Posts

Sanders New Member

Sanders

Posted
Posted

Hi everyone,
Last year I bought in an outlet store 4 watches, few of them with battery. Among them there is one Zodiac, when I bought it was not ticking so I thought it was just a battery problem, although the watch was brand new. This year I decided to start using it so I changed the battery and I turns out that is not ticking.
I am even afraid to go to the watch store and ask how much the reparation will cost. I have tried with 2 new batteries, but noting is moving, I event think that these kind of watches have not repair. Hopefully I am wrong. Any hints what to do?
Thanks,
Sanders

zod1.thumb.jpg.5c70d65ef25037a965f9d3eb1937f6de.jpgzod2.thumb.jpg.fa87622d3a9211387b736e8e46e4dcf6.jpg

 

Link to comment
Share on other sites
Gpsluvr WRT Addict

Gpsluvr

Posted
Posted

The battery compartment should have an orange insulator at the bottom of it, with the contact bar sticking above it. The battery goes in button or negative down and on top of that contact bar. Make sure the insulator is there and that you didn’t accidentally bend the contact bar. It is usually a very thin gold plated bar and breaks off easily. Can you check these things and send us a photo of the movement with the battery out and beside it? It probably has an inexpensive Swiss Ronda movement that won’t cost too much to replace if it still doesn’t work. Look closely at the red coil that is close to the battery. It shouldn’t have any marks on the wires. Sometimes that gets scratched when changing the battery and it will be ruined more than likely. If everything looks good, then one other trick that works on movements that are good but just locked up with dust or from years of inactivity, is to place a very small drop of lighter fluid on top of the movement in he center where the jewels are. Then blow it dry with canned air from the computer department of a store. Don’t put the back on if it is not completely dry as the moisture will condense on the crystal from the inside. Let us know how it goes. Steve


Sent from my iPad using Tapatalk Pro

Link to comment
Share on other sites
Sanders New Member

Sanders

Posted
  • Author
Posted

Thank you Steve, appreciated your guidance and time for helping me.

I opened the watch, the insulator was still there between the bottom and the battery. I checked that the golden plate contacts properly to the battery. As far as I can see, the red coild is intact.

I manually moved back and forth the watch's date and time, and also blowed compressed air as you suggested, but unfortunately is still dead.

I don't have any watch lighter fluid and I am afraid to keep opening the rest of the screws. Basically I have a cheap watch repair kit and none of the screwdrives are small enough for those.

Now I could consider changing the movement depending on the price, otherwise I will just take it to repair.
I was checking movements on eBay but I am not sure if there are compatible movements for this watch, because I didn't find anything for Zodiac ZO8550.

Thanks again!

Sanders

a.jpg

b.jpg

c.jpg

d.jpg

Link to comment
Share on other sites
  • 2 weeks later...
Sanders New Member

Sanders

Posted
  • Author
Posted

Hi,
I went to a well known jewelry in Vienna and the woman told me that she didn't have a tool to open this kind of watch ( confused face).
Then I went to another one and they told me, sorry we don't repair Zodiac.
The last one, I went to a Fossil store and they told me they have official support for Zodiac, but they need to send the watch to France...
I don't want to send my watch to France so I will try to fix it myself.

Current status:
I reached this point where I am not sure how to remove the front properly.
Once I remove the hands, how do I remove the blue cover?

 

 

 

g.jpg

f.jpg

Link to comment
Share on other sites
Sanders New Member

Sanders

Posted
  • Author
Posted

Finally I found a store that repaired this watch. It costed 20€ including battery change. I am happy that I didn't chose to replace the movement myself, I would have spent 25€ for the new movement and probably I would have not be able to fix it properly.
Thanks for the guidance and support
Sanders

Link to comment
Share on other sites
 Share
Go to topic listing


  • Recently Browsing

    • No registered users viewing this page.

  • Topics

  • Posts

    • Klassiker
      Epilame / Fixodrop

      By Klassiker · Posted

      I agree with @JohnR725. Oil on an epilamed surface is essentially the same as water on a waxed surface. The same physical properties are at work (surface tension vs. adhesion). 
    • Waggy
      Without Our Forum

      By Waggy · Posted

      I think we all get a lot out of this group, and it has been pivotal in my development by the sharing of knowledge, experience and learning from more seasoned experts such as @JohnR725 and others (you know who you are!) as well as fellow novices. I think that having a backup communication plan in reserve so that if there is a future problem just makes good sense. I don't think anyone is trying to undermine the forum, but if something unthinkable happens, like the Ranfft website for example, then it would be good if those who are willing can still keep in contact. Speaking personally, and I know I risk a charge of heresy, it would be good if Mark could be a little more visible in this forum, and maybe give any insight from time to time on the future/progress of forum and instructional videos etc. even if its just to confirm the status quo. I appreciate he is a busy man with a full time job, but so are most of the rest of us and to post a few lines every now and then shouldn't be too much to ask to reassure the restless villagers. Best outcome for me would be a message saying something along the lines of: "Hi guys, all good, no planned changes... enjoy the forum, will message again next month!" Just my two cents.
    • Endeavor
      Omega cal. 565 - low amplitude

      By Endeavor · Posted

      A nice looking watch !! Did you try 9010, instead of the 9415, on the pallet jewels / escape wheel? And if you did, did you notice a difference?
    • Waggy
      404 Club

      By Waggy · Posted

      Knocked out another 404 last night...when you are in the zone! This watch was a non-runner which I picked up as part of a lot of 8 watches, so works out to be $3.12 per watch. Before:   And the finished watch, new crown and stem and the crystal was cracked so was replaced. I also replaced the mainspring as the original was the old steel type spiral and very 'set' - all else is original: The Movement was a AS 1686, but in reading around a little the ACCRO watch company were sued for their use of the five point crown on their Jacques Pere range as it resembled Rolex, see below: ACCRO then reverted to just ACCRO on their watches - I have done some sniffing around the internet and haven't seen another example of ACCRO and the crown together on a dial so maybe I have something unusual, or maybe I was looking in the wrong places 🙂.  
    • Bonefixer
      Pocket watch escape wh

      By Bonefixer · Posted

      This watch was damaged when I got it. I didn't break the escape wheel pivot, and I bodged a fix with epoxy to see if I could get it running. I'm not yet ready to get into lathe work, or shellacking jewels, and may never be. But I'm learning plenty with each watch I tackle. 
×
×
  • Create New...