Jump to content

eta 2824-2 date wheel removal

apollo1965
 Share

Recommended Posts

jdm Distinguished Member

jdm

Posted
Posted
36 minutes ago, apollo1965 said:

Anyone aware of any videos or tutorials on how to remove and replace date wheel on eta 2824-2. Cant seem to find any on google.

The very best way to learn is with Mark's lessons:

https://www.watchrepairlessons.com/

Also, we have a dedicated section where is considered polite to introduce oneself even before asking questions.

Link to comment
Share on other sites
jdm Distinguished Member

jdm

Posted
Posted
6 hours ago, apollo1965 said:

Thanks will check it out

I'm pretty sure that Mark also made videos about the 2824, that would answer your specific question but the lessons teaches how to do things correctly, and why.

Link to comment
Share on other sites
anilv Distinguished Member

anilv

Posted
Posted (edited)

ETA came up with an easier way to get the date-wheel in place in the 2824 compared to other older movements where you need to mess with springs and jumpers and hope pray the jumper spring doesn't fly off.

You install the jumper and its cover first, then align the teeth on the date-wheel with the slots in the edge of the cover and push the jumper aside. Once the date-wheel is in place the jumper will align the date wheel correctly. Finally install the minute wheel cover and screw it down. This completes the date-wheel installation.

A bit unusual if this is the first time you've worked on one. Trouble is we're so used to this movements we expect everyone to know this!

Anilv

 

 

Edited by anilv
Link to comment
Share on other sites
 Share
Go to topic listing


  • Recently Browsing

    • No registered users viewing this page.

  • Topics

  • Posts

    • mikepilk
      Balance wheelwheel crooked

      By mikepilk · Posted

      As with every skill it watchmaking, it takes practice. Notice at the top of the document it says, "Practical work - 40 hours".  I can get the balance wheels 'close enough' to flat, but never seem to get them perfect. Same with gear wheels. Guess I need more practice.
    • transporter
      Beat adjustment

      By transporter · Posted

      Has it got a beat adjustment on the platform or is it a fixed hairspring? in short what you are looking at to get it just about in beat is to get the roller jewel sitting dead centre between the banking pins. So remove the platform and take of the pallet fork and escape wheel to give you clear line of site, sit the platform with the balance in place and with it level look between the banking pins and see if the roller jewel is sitting between them, if it is nice and central its there or there abouts in beat, if its not the the position of the pinned end of the hairspring needs to be adjusted to move the roller jewel into the correct position, thats why I asked if it has an adjustment on the platform or not, if it has its an easier job. 
    • MapleWood
      Help - London Elliott Mantle Clock Night Silence

      By MapleWood · Posted

      I've managed to adjust it. I'm going to try and explain it as well as I can with my limited horology knowledge but I hope it helps someone in the future. There is a cam to the right of the front plate as shown in the picture. As the clock ticks along, the pin indicated in the gear comes around and slots into one of the silencer cam gaps, turning the cam. The pin completes a full rotation in 2 hours. To adjust the cam to start at the right time set the clock to just before 7. I did 6:45. Then I turned the silencer cam anticlockwise, which spins freely, until it pushed the silencer lever up and was placed just before the drop. Just before the 7AM indicated in the picture. All I then had to do was progress the hands to 7-7:15which made the pin slot into the silencer cam gap and turn the cam so the lever comes down again, unsilencing the clock. That was it. If anyone comes across this issue again I'd be happy to assist. Thanks again to everyone that helped. Hey Transporter! Thanks a lot for the reply. That was a really good explanation and I'm sure it would have made my troubleshooting a lot less painful haha. I'm sure someone will find it useful in the future. Thank you again for taking the time to try and help me out with this.
    • Waggy
      Epilame / Fixodrop

      By Waggy · Posted

      Now I'm completely confused, it would appear that the epilame  is oleophobic  as @Marc states: This oleophobic  behavior can be seen as beading of the droplet (as above) which stops the oil spreading which is supported by what we observe on treated/untreated cap stones (for example), but as @VWatchie states this should make the drops more mobile and is supported by the literature:   A review on control of droplet motion based on wettability modulation principles design strategies recent progress and applications.pdf   However the hole point is that we have less mobile oil so an oleophobic  would see to be the opposite of what we want. In fact this beading and high mobility are desirable properties in things like smart phone covers, see below.  I am fairly sure that epilame doesn't make the droplets more mobile, so maybe its a strange coating with dual properties that are both oleophobic (beading) and cohesive/adhesive resulting in low mobility?? This may explain the high price??  
    • nickelsilver
      Balance wheelwheel crooked

      By nickelsilver · Posted

      The description there is exactly how it's done, and it's very well written!
×
×
  • Create New...