Jump to content

Navi 806 bezel refit incase anyone’s as stupid as me

quantieme
 Share

Recommended Posts

quantieme WRT Addict

quantieme

Posted
Posted

So I recently took apart cleaned and serviced this navitimer and I also completely took apart the case which included the bezel ring which sits under the inner case insert, when I went to put the bezel back on it took a lot of pressure but I heard a snap as it seemed to click into place but every time I released pressure the bezel pinged off, I tried putting it back without the crystal, I tried gently heating the bezel to expand it incase it was tight but same result, 2 Hours later I had just about given up when a thought occurred to me and I had a look at the bezel ring under my loupe and sure enough there was an almost imperceptibly lip on one edge and it should have been on the top but I had fitted it upside down, DOH! I just could not see it with the naked eye at least not with my old eyes. It taught me a lesson that even something as simple looking as that ring has to be fitted a certain way and I shall pay more attention in the future as to how things are fitted. I am putting this on here because I tried searching the www for answers but could find nothing so it might help someone in the future.

Link to comment
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Restore formatting

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

×
 Share
Go to topic listing


  • Recently Browsing

    • No registered users viewing this page.

  • Topics

  • Posts

    • HectorLooi
      Battery

      By HectorLooi · Posted

      Usually the coiled spring contacts the piezo sounder and the finger spring is the ground.
    • Waggy
      How to store one dip

      By Waggy · Posted

      So I checked with my friendly local lab supplier and they can supply the following in 2.5 lt bottles: Tetrachloroethylene (B-Dip) - approx ￡65 Trichloroethylene (one-dip) - approx ￡43 n-Heptane 99% (Essence of Renata) - approx ￡35 Hexane - approx ￡45 I can't import or buy locally the 'real' products, hence the raw chemicals above. What do you think would be my best option? I'm edging towards Trichloroethylene - I know there are greater health risks, but given the very small quantities used for each treatment and 99.99% of the time it will be sealed in a jar, I think any risk is vanishingly small? This is mainly due to its assumed superior cleaning properties, or from the experience of this group, is the extra cleaning noticeable compared to its safer alternatives?
    • Kkramme
      Blew it with a coil

      By Kkramme · Posted

      Unfortunately after much investigation, apparently the coil has been discontinued! Shall I get my service guy to try the solder or the conductive paint? 🎨 Final recommendation please🙏
    • Dmitry
      Eta 2970-1 rotor mount stops watch

      By Dmitry · Posted

      Here are the pics of the bridge. Looks correct, but as soon as I screw on the rotor, the watch stops. Video here: https://1drv.ms/v/s!ArG5E62RGctxjokY5ws85BzuJLVakA   Pics. Might have figured it out. I have been working on this watch for a while and since I got it as a non runner in a terrible shape, there was no guarantee that parts were proper. I think the main screw that was used on the rotor was too long, so it was stopping the main train. As soon as I fished out a much shorter and larger headed screw, things were good again. Please celebrate with me.  
    • KarlvonKoln
      B-Dip residue?

      By KarlvonKoln · Posted

      One-dip or naphtha should be safe, but are you sure it isn't magnetized?  I would also check that.  Although, if that balance is from an Elgin 760 0r 761, I would think it would have a hairspring of non-magnetic alloy.
×
×
  • Create New...