Jump to content

ISO Swiss VS Cousins Watch gaskets


Tmuir

Recommended Posts

I'm looking at buying a box of flat rubber watch gaskets and looking at Cousins they have their own brand and ISO Swiss gaskets.

The Swiss gaskets are 8 times more expensive than the Cousins gaskets.

Are they really 8 times better?

Reading between the lines I think the Swiss gaskets are Nitrile rubber, whilst the Cousins ones aren't.

Are the Swiss ones really worth the extra cost? I don't mind paying more if I am getting a better product, but don't want to pay more just for the name 'Swiss' on the box.

I will add hopefully next year I will be starting to service other peoples watches, so will be using the gaskets for not just my watches buy for paying customers too, so don't want to save myself a few dollars now that could come back and bite me if the cheap gaskets fail in customers watches.

Edited by Tmuir
Link to comment
Share on other sites

That's a tough one, I have every confidence with my battery replacement reseals in cousins gaskets, and the servicing i do on mechanical watches at this stage of my career tends to be on old watches that are splash proof at best anyway, so I don't think about that much.

If you're working on modern expensive modern autos that are 50m and up, and you're promising them resealed then it might just be worth the extra expense, (If its quartz it will need to be resealed with the next battery change in a couple of years anyway, so dont worry) I dont think anything would come back to you in any time frame that you could take responsibility for, but given that some of these watches go a decade without anyone looking at them, the customer might find 8 years after the service they jump into a pool and it floods, now obviously thats not really your fault or responsibility, even if it could have been theoretically prevented with an expensive gasket that would degrade more slowly, you cant promise people that their watch will be waterproof for a decade without maintenance. so it shouldn't cause you any problems, but perhaps more of an ethical consideration for the owners of the watches and what they might face way off down the line and whether that hypothetical situation would cause you to lose any sleep. 

To answer more directly, as chopin says they're a bit better, but not 8 times better. 

Edited by Ishima
  • Like 2
Link to comment
Share on other sites



  • Recently Browsing

    • No registered users viewing this page.
  • Topics

  • Posts

    • It started well. Got the clip off, cleaned in B-dip, bit of grease, then ping 😫. Lost the clip trying to refit it.    I'll get a replacement from eBay. 
    • I used Google Lens on the pic and it suggested "motorcyle belt punch". And googling pics of that does show very similar tools. The end on mine is sharp, and does look suitable for punching holes in leather. I've no idea what belts on motorcyles would need piercing? The hole is about 1/4", so I cannot see a use in watchmaking. So, why have we both found one in a collection of watchmaking tools? 
    • You often see the term used on old watch part boxes.  Staffs for bracelet watches, timing washers for bracelet wstches etc.
    • The Boro has changed quite a lot over the last 20 years, and not for the better. I actually moved out of the town 15 years ago to a small village not far away. Thanks for the pdf! Looks a great read. I'll get it printed today and put it on my work bench!
    • Not having all the fancy equipment, this is a way I came up with. I never said it was the best, the most ideal or the safest way. Working on balances is always a delicate task whereby full concentration & common sense should prevail. I was well aware of the "dangers" / short comings involved, hence my "warnings", as quoted above. The balance wheel of the Omega was nice true, flat and one could clearly see how much gap there was left before the grinding wheel would touch the balance wheel. I stopped when the generously applied diamond paste started to touch the rim of the balance wheel, which turned out to be with a seat thickness left of 0.1mm. Tapping the remainder of the staff out went easy and flawless. My idea of penning this article was to show/share a way which, in my case, perfectly succeeded. If deemed to risky, or if the balance wheel is not true or has a wobble, other methods have to be followed.
×
×
  • Create New...