Jump to content

staiger quartz astronometer

graham123

By graham123
in All Things Clocks

 Share

Recommended Posts

graham123 Member

graham123

Posted
Posted

hello back again.managed to get this staiger clock from a auction,and really pleased with it.i have never come across this type of clock before,so i intend to keep it.the same auction had a vintage walker time grapher,again never seen one before,and think my friend bought it.sorry about no pics,i really struggle to upload pics

Link to comment
Share on other sites
oldhippy Distinguished Member

oldhippy

Posted
Posted
10 hours ago, graham123 said:

thanks clock boy,this was the auction picture i used.the case is good old hippy,and all the functions are working well.i am guessing the clock was made in the eighties,with a limited manufacturer run    

I would think that is a safe bet around the 1980's. If it is a limited edition it should have a number with some sort of paper work, a limited edition could be any number, a clock could be made in its thousands and still be called a limited edition.

Link to comment
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Restore formatting

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

×
 Share
Go to topic listing


  • Recently Browsing

    • No registered users viewing this page.

  • Topics

  • Posts

    • KarlvonKoln
      B-Dip residue?

      By KarlvonKoln · Posted

      One-dip or naphtha should be safe, but are you sure it isn't magnetized?  I would also check that.  Although, if that balance is from an Elgin 760 0r 761, I would think it would have a hairspring of non-magnetic alloy.
    • Curare
      Spell Check

      By Curare · Posted

      Hi, Is there a spell check function available when you are posting ? Regards CJ
    • Curare
      Replacing armoured crystal in a front loading watch case…

      By Curare · Posted

      Hi John I just did a Seiko Lord-Matic a front loader without a split stem, I used a crystal lift to remove it, although I had to have it that tight I though I was going to break the lift before the crystal would budge. So I decided that the press would be a better option as I think crystals with tension rings resist a lot of compressing. I used a crystal press to repalce it and the bezel with no issues, obviuosly a different watch to the Omega. I just took my time and kept inspecting the installation progress bit by bit Regards CJ
    • Zendoc
      Replacing armoured crystal in a front loading watch case…

      By Zendoc · Posted

      Hello All, I’m replacing the crystal in an Omega Dynamic, # 165.039, which houses a cal 552, installed through the front of the case. The replacement Sterncreuz crystal is, like the original, with tension ring. I removed the crystal using a compressed air technique to pop it out.  (I have a crystal lift, but I’m always fearful of marking the crystal edges and so avoid using it as much as possible). Now to the replacement -  any tips on putting the crystal back in?  Am I obliged to using my dreaded crystal lift to complete the task, or how about a crystal press?  I’ve put lots of crystals in using a press, but never with the movement in the watch. The thought of using one with a front-loader makes me very nervous, with the fully assembled watch sitting under the press. How would more experienced folks proceed here? Any advice, gratefully received… John Down Under…
    • Neverenoughwatches
      AS 554 from 1930

      By Neverenoughwatches · Posted

      No thats straight out of the watch as i found it the balance wheel is almost as bad. I've never seen so much material removed.
×
×
  • Create New...