Jump to content

How i make a watch stem

szbalogh
 Share

Recommended Posts

szbalogh Super WRT Addict

szbalogh

Posted
Posted

A friend of mine asked if i want to make a stem for him. I have improved my hardware and wanted to try so happily accepted :)

Not in the Dremel now. Here the pulley wheel is serving as a dividing plate with 4 holes making sure that the rectangle cross-section will be perfect. Turning with help of a microscope, no loupe at all. 

2016-10-07_15_18_06.jpeg

2016-10-07_17_49_00.jpeg

A thin glass strip is hot glued on the "T-rest" which has two purpose. The file is sliding on it easily and it is making sure that the sides will be parallel.

2016-10-07_17_49_08.jpeg

2016-10-08_14_59_38.jpeg

Still a lot to file down.

The workpiece is a spoke of a Chehoslovak Favorit road racer. Even tungsten carbide is softer if hardened.

  • Like 5
Link to comment
Share on other sites
szbalogh Super WRT Addict

szbalogh

Posted
  • Author
Posted (edited)

Finaly i got something similar to a winding stem.... for the 6th try.... 

20161016_142231.jpeg

M1.2 thread done. The stem here was turned down to 1.15mm to make sure it wont break while tapping. 

20161017_181000.jpeg

After heated to red and dropped in brine. It is so hard and brittle, i can hear it whizzling near my ear :)

20161017_191123.jpeg

Using my special top quality heating pan

20161017_192510.jpeg

Annealed. Not as shiny like on pictures one can find on pro-watchmaker school sites, but the color tells me the temperature and that is important.

20161017_192910.jpeg

 And the best thing is, i dont had the movement. So there might be a big surprise for the guy i made it if it wont work :)

Edited by szbalogh
Link to comment
Share on other sites
szbalogh Super WRT Addict

szbalogh

Posted
  • Author
Posted (edited)
On 2016. 10. 18. at 0:00 AM, MilTimeCan said:

I am in awe.

Wow, I worked on a lot of plastic model aircraft parts in my younger days, but I have never seen anything like this. 

Sir, you are a pro !

Not a pro for sure :) Just so excited while discovering this new watchmaking world. For an experienced watchmaker this is an every day job :) And i am sure i could make it better. For example if i had a glass fiber scratch brush, then the bluing would be better. Also i am not satisfied with the setting lever slot.The rectangular edges here are not perfect. I will have to grind a better graver to cut this type of slots.

Made a video of this project, threading included.

 

Edited by szbalogh
  • Like 5
Link to comment
Share on other sites
 Share
Go to topic listing


  • Recently Browsing

    • No registered users viewing this page.

  • Topics

  • Posts

    • mthomas828
      Balance staff sourcing?

      By mthomas828 · Posted

      Hello, I am about 5 months into watchmaking and I love it!   The attention to precise detail is what really attracts me to it. (and the tools!) I am working on a 16 jewel 43mm pocket watch movement.   There are no markings besides a serial number (122248) .  The balance staff needs replacement. The roller side pivot broke off.  I successfully removed the hairspring using Bergeon 5430's.  I successfully removed the roller using Bergeon 2810.   Did i mention I love the tools?! I removed the staff from the balance wheel using a vintage K&D staff removal tool  with my Bergeon 15285 (that's the one that comes with a micrometer adjustment so it can be used as a jewel press as well as a traditional staking tool...it's sooooo cool...sorry..  can you tell i love the tools?) No more digressing..  I measured the damaged staff in all the relevant areas but I have to estimate on some because one of the pivots is missing. A = Full length  A= 4.80mm  (that's without the one pivot...if you assume that the missing pivot is the same length as the other pivot (I'm sure it's not)  then A = 5.12 mm...(can I assume 5.00mm here?) F=  Hair spring collet seat  F=  .89mm   (safe to assume .90 here? .. I am sure that my measurement's would at least contain  .01 mm error ?) G = balance wheel seat  G = 1.23 mm  (1.20mm?) H  =  roller staff  H =  .59mm  (.60 mm?) B  = bottom of the wheel to roller pivot   B  = 2.97mm  (3.00 mm?)     here I am estimating  again because this pivot is missing. So my friends, and I thank you profusely,  can you point me in the right direction as to how to proceed? Do i buy individual staffs?  or an assortment?   Since I don't know exactly the name of the manufacturer, will that be a fatal hindrance?   Tbh, I'm not even sure what country of origin this movement is. Thank you!    
    • Neverenoughwatches
      Epilame / Fixodrop

      By Neverenoughwatches · Posted

      Thats why i asked that question earlier, what happens if lubrication is placed directly on top of epilame ?  As opposed to walled within its non epilamed area . I'm not saying its right, i have no idea , just asking questions. 
    • JohnR725
      Epilame / Fixodrop

      By JohnR725 · Posted

      thinking of where epilam should be removed did you know there was a patent that covers this? At least for the escapement I'm attaching it. GB1057607A-1 epilame.pdf
    • LittleWatchShop
      Movement holder made with 3D printer

      By LittleWatchShop · Posted

      Back home...printing now.  Will report results
    • VWatchie
      Epilame / Fixodrop

      By VWatchie · Posted

      Oh well, if Master @nickelsilver says it's the way to go, then it is the way to go! I stand corrected! 🫡 Are there any other places where you're supposed to remove the epilame from the contact point of rubbing? I don't think so! Thanks for the effort @Neverenoughwatches, much appreciated! 🙂👍
×
×
  • Create New...