Jump to content

ETA 955.412

Taartstudio
 Share

Recommended Posts

Cad101 Super WRT Addict

Cad101

Posted
Posted

Does it quick set ok or does it feel stiff. Is your date wheel locking spring bent too far causing too much friction with the date wheel.

If you've put it all back together exactly as Marks video I cant see why its not working.

Link to comment
Share on other sites
Cad101 Super WRT Addict

Cad101

Posted
Posted

Looks like its time to strip down the dial side date workings and check your work I think. And when you do leave the dial off and movement out of the case so you can study the dial ring as it auto changes you might spot the problem. If it changes ok its something to do with the dial have you put the dial washer back in place.

Link to comment
Share on other sites
  • 4 years later...
keigokanzaki New Member

keigokanzaki

Posted
Posted

Sorry for waking up an old thread. I experienced the same thing with my Tag Heuer wk1211, which uses this movement. Google brought me to this discussion.

Originally, when changing battery, the store suggest me to replace the movement with a new one because he spotted signs of battery leakage. So I agree with him. However, after the change, the date wheel sometimes stuck on certain dates. I took it back to service, but it seemed they cannot fix it.

I wonder if the OP or anyone else have solved the problem?

Link to comment
Share on other sites
jdm Distinguished Member

jdm

Posted
Posted
4 hours ago, keigokanzaki said:

 I wonder if the OP or anyone else have solved the problem?

Either give the watch to a reputable repairer that works on quartz (there aren't many, you can try Archer Watches), or replace it, easier said than done since it's discontinued.

There is no clear better cost and inconvenience choice between these two, so good luck. 

Link to comment
Share on other sites
keigokanzaki New Member

keigokanzaki

Posted
Posted
14 hours ago, jdm said:

Either give the watch to a reputable repairer that works on quartz (there aren't many, you can try Archer Watches), or replace it, easier said than done since it's discontinued.

There is no clear better cost and inconvenience choice between these two, so good luck. 

Sending the watch across the globe to Archer Watches is sadly almost impossible for me (I lived in South East Asia) :lol:

I think I made up my mind to leave the watch as it is, and start saving for a new watch instead.... probably an Omega.

thanks for your reply, man

Link to comment
Share on other sites
jdm Distinguished Member

jdm

Posted
Posted
1 hour ago, keigokanzaki said:

Sending the watch across the globe to Archer Watches is sadly almost impossible for me (I lived in South East Asia)

You didn't mention you country but for the record I've shipped in and out registered post without any problem from various ones in SE.

If your concern is about customs duties then the best approach is to declare a low value both ways, and save the outgoing shipping papers as "watch sent for repair", when returning the form will say "return from repair", so you will have the correct explanation in case of customs inspection.

Link to comment
Share on other sites
keigokanzaki New Member

keigokanzaki

Posted
Posted
21 hours ago, jdm said:

You didn't mention you country but for the record I've shipped in and out registered post without any problem from various ones in SE.

If your concern is about customs duties then the best approach is to declare a low value both ways, and save the outgoing shipping papers as "watch sent for repair", when returning the form will say "return from repair", so you will have the correct explanation in case of customs inspection.

Ah pardon me, I live in Indonesia. From my limited personal experience, it's kinda hard to find an honest reputable watchmaker around here. My previously mentioned Tag was serviced by an authorized service center earlier but to no avail. Since that service center can accept shipped watch but refuse to ship it back (I have to get it myself and we live in different city, plus the pandemic makes more difficult to travel), I'm hesitant to send my watch to them again.

Very well, I will give your advice some thought.

Link to comment
Share on other sites
jdm Distinguished Member

jdm

Posted
Posted
1 hour ago, keigokanzaki said:

I live in Indonesia. From my limited personal experience, it's kinda hard to find an honest reputable watchmaker around here.

I know of at least a member here from a bordering country, if he reads this and is interested he may contact you directly.

Where there's a will there's a way.

Link to comment
Share on other sites
 Share
Go to topic listing


  • Recently Browsing

    • No registered users viewing this page.

  • Topics

  • Posts

    • Knebo
      Epilame / Fixodrop

      By Knebo · Posted

      Yes, I was referring to the (jewelled) gear train with HP (most of the time, I use 1300, but when Rolex says 1000, I'll use 1000).
    • JohnR725
      Without Our Forum

      By JohnR725 · Posted

      did I miss the update of the message of something changing?      
    • JohnR725
      Epilame / Fixodrop

      By JohnR725 · Posted

      I suppose it would depend upon what your lubricating with those? for instance what does the manufacturer say about those lubricants? I have a PDF from the manufacture and a rather peculiar statement found on the bottom of the chart. my suspicion is the reason the recommending would be without epilam the HP oils like the spread except when they're in Ruby jewel's with steel pivots. tableEN lubrication 2020.pdf
    • oldhippy
      Is this a 'hack' ?

      By oldhippy · Posted

      These types of hairsprings become weak with age and very fragile. Which I expect it is that giving you trouble, and that wheel is not the correct one, if it were not bent I don't think the movement would run as the teeth are not the correct height. The problem you have is price which depends on you. It can be repaired but is it worth it to you, because there is little value in the clock. A wheel can be made and hairspring replaced. Or hang on to it and keep looking on ebay which is your best bet for replacement parts or even a complete movement but it will be like finding a needle in a haystack. 
    • Knebo
      Epilame / Fixodrop

      By Knebo · Posted

      I did that also for a few movements - well, mainly in/around the train jewels. I made big efforts to epilame the mainplate WITHOUT getting Epilame into the Pallet fork jewels (where it's not supposed to be, right?). I made litte barriers with Rodico around that jewel and used drops from a syringe to apply on the rest.  However, I've now stopped doing this. For three reasons: 1. It's a hassle and consumes more of this liquid gold. 2. I didn't see the need when using HP1000/HP1300 lubricants and grease for most part. The two places where I'd use 9010 (i.e. escape wheel and balance) receive Epilame in specific places... or the cap-jewel-setting of the balance suspends the oil sufficiently be capillary action (see my "conflict" about using Epilame on the balance jewels).  3. Lastly, and here I really wonder about yours and others' experiences: I felt that applying Epliame to the train jewels left them looking hazy (borderline dirty) compared to the (painstakingly achieved) sparkly clean results of my cleaning process. I just can't help but think that the Epilame residuals would mix with the oil and cause more friction/wear. I don't know.    simple: it'll stay there. It won't move any further. That's exactly what is happening if you epilame a cap stone. You end up placing the 9010 right on top of the epilame and the oil will sit nicely on that spot.
×
×
  • Create New...