Jump to content

Hello all

QatWand

By QatWand
in Introduce Yourself Here

 Share

Recommended Posts

QatWand New Member

QatWand

Posted
Posted

I am a complete amateur who can't resist taking things apart. I know just enough to be dangerous. 

The question I need an answer to has to do with a carriage clock, but I hear they are similar to pocket watches, so here goes:

I need to replace the hairspring  for this clock. I bought a package of  assorted hairsprings, but none of them is the right size. What are the specs for a hairspring and how do you measure it?

Diameter of the spring? Diameter of the middle part? I don't know the correct terminology. Thanks.

Hairspring.jpg

clockboy Distinguished Member

clockboy

Posted
Posted

Welcome to the forum, enjoy. Replacing a h/spring is not straightforward.. it must be the correct strength & length. Looking at the picture the h/spring it looks in c good v condition. 

oldhippy Distinguished Member

oldhippy

Posted
Posted

Thank you for your introduction and welcome to this friendly forum.

We all look forward to your contributions and continued involvement. 

Carriage clocks are nothing like pocket watches. 

The photo is of a cylinder balance wheel, hair spring and balance cock and screw. Can you show me the movement. It might be better to buy a second hand complete platform. 

  • 4 weeks later...
CYCLOPS WRT Addict

CYCLOPS

Posted
Posted

Welcome, if the pivots on the balance wheel are good just re-pin the hairspring showing, I am assuming it is the original and only about 2-3 millimeters have been lost, the hairspring stud looks to be still in the bridge/cock....

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Restore formatting

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

×
 Share
Go to topic listing

  • Recently Browsing

    • No registered users viewing this page.

  • Topics

  • Posts

    • Nucejoe
      Greetings from Whidbey Island.

      By Nucejoe · Posted

      Hello and welcome to the WRT forum.
    • JohnR725
      A lathe with indexing that won't break the bank?

      By JohnR725 · Posted

      interesting video nice to see the machine what it can do now I wonder what it costs and I'm sure it's not in my budget. Plus the video brought up questions but the website below answers the questions? What was bothering me was the size of his machine 4 mm because I thought it was bigger than that? But then it occurred to me that maybe they had variations it looks like four, seven and 10. With the seven and 10 being the best because way more tool positions in way more rotating tools. Although I bet you all the rotating tools are probably separate cost https://www.tornos.com/en/content/swissnano   Then as we been talking about Sherline. Just so that everyone's aware of this they have another division their industrial division where you can buy bits and pieces. I have a link below that shows that just in case you don't want to have the entire machine you just need bits and pieces. https://www.sherline.com/product-category/industrial-products-division/   Let's see what we can do with the concept I explained up above and bits and pieces. For one thing you can make a really tiny gear very tiny like perhaps you're going to make a watch. Then another version the center part is not separate it is all machined from one piece. Then fills gear cutting machines have gone through multiple of evolutions. A lot of it based on what he wanted to make like he was going to make a watch unfortunately eyesight issues have prevented that. Another reason why you should start projects like this much sooner when your eyesight is really good or perhaps start on watches first and then move the clocks then local we have from the industrial division? Looks like two separate motors and heads. Then it's hard to see but this entire thing is built on top of a much larger milling machine as a larger milling machine gave a very solid platform to build everything.   Then like everything else that had multiple generations are versions the indexing went through of course variations like above is one version and the one below was the last version. Now the version below I mentioned that previously and somewhere in the beginning to discussion and somebody else had one in their picture. As it is a really nice precision indexing. Then I wasn't sure if I had a the watch photos here is his unfinished watch. No he wasn't going to make a simple watch like none of his clocks were simply either what would be the challenge and that.    
    • Titanium
      Lab Coats

      By Titanium · Posted

      Use a Portwest Howie lab coat. They are the biological type so they have tapped cuffs so you don't end up getting the loose cuffs of normal lab coats catching everything. 
    • Titanium
      Chinese tools debate

      By Titanium · Posted

      Some of the Chinese tools ae great and can be purchased at a fraction of the price of Swiss ones, some are complete garbage and some I'm convinced are coming out the same factory as the branded ones.
    • caseback
      Calendar work certina 25-651

      By caseback · Posted

      I found this string about this problem. I've not gone through it all, but I believe it also mentions making a spring. If not in this string, the info is online.
×
×
  • Create New...