Jump to content

LORUS stainless steel watch strap


Imac23

Recommended Posts

I'm new to this forum so I hope my question is not too simple! I woke up with my LORUS watch strap broken in bed (I usually take it off) It looks like the pin is broken. The measurement between the lugs on the watch is 22mm. Is 22mm the size of the pin I need? I saw a 22mm pin double flanged, heavy duty - online. Should I buy this?

Is it double-flanged?

Thanks.

Photo on 27-11-2023 at 10.04.jpg

Edited by Imac23
spelling
Link to comment
Share on other sites

22mm will be the size to order, from your photo it does look like it’s double flanged. If you can measure the diameter in the middle of the broken spring bar and order parts the same. When I get a broken spring bar like this I usually change both as they are likely to be similarly worn and the other could break soon, not a big deal if you’re in bed but it hitting a concrete floor or the like can be a problem.

 

Tom

  • Like 2
  • Haha 1
Link to comment
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

×   Pasted as rich text.   Restore formatting

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.



  • Recently Browsing

    • No registered users viewing this page.
  • Topics

  • Posts

    • These are the places where I oiled with HP 1300...  These are the places where I oiled with HP 1300...  I can see that the cannon pinion is moving as it should once I installed the pallet fork. I created a small video but was not able to upload it. It is a mov file type. I need now to source a GR4014X mainspring, a stop ever #9433 and both calendar disc as the days/dates are peeling out... This is the mido watch which holds the ETA Movement.... I just want to thanks all of you guys for your help, specially @eccentric59 who nailed it! So, I would consider this case as closed unless of course any question from any of you... Best regards Fernando     I could not download the file... I will tray to located. Many thanks. 
    • Thanks a lot everyone!  I'll update you as soon as a final decision has been made by my friend (and depending on her decision, what I may find inside). 
    • Thanks Marc, clearly I have a lot to learn about metallurgy. I’d expect the cutting of tool or spring steel to be a lot harder to cut into a precise shape- I expect I’d have to anneal it first? 
    • Unfortunately if you have used mild steel you will have little hope of hardening and tempering it, it simply doesn't contain enough carbon. You need to use a steel with a higher carbon content like tool steel or spring steel. One good source for this is engineers feeler gauges which can be picked up relatively inexpensively and provide a range of thicknesses of material. this will then harden and temper in pretty much the way you have described.
    • Thanks for this excellent tutorial and very fine illustrations @Jon! Really first class! 👍 I noticed that your image was a bit too small to read with ease, so here's a larger copy of it. I summarized @nickelsilver's method for adjusting beat errors to the following, but you can find all the info in the thread I linked to: “For everyday work, from the smallest ladies’ movements to marine chronometer, I set the balance with the cock on a bench block so the roller table is in a hole, balance on the block. Lift up the cock and move it over- not flipping it, just moving laterally, until I can see the slot in the hairspring collet, get in there and adjust (for tiny watches this is usually with an oiler, larger, a small screwdriver). Go back in the watch and check on the machine. I hold a balance arm of the rim with tweezers while moving the collet.”    
×
×
  • Create New...