Jump to content

How yemk install screws to call the phone it's not riding on the enabled

Khaledabdwatch
 Share

Recommended Posts

grsnovi Distinguished Member

grsnovi

Posted
Posted

You might consider using another translator - your headline makes no sense in the context of watchmaking.

You are showing a CITIZEN dial. I assume both front and back? If so, the back side has no location pins, so I'm assuming you locate the dial based on the day/date window?

I'm not familiar with how CITIZEN attaches their dials - other brands attach the dial by means of really small screws through the side of the movement however those screws typically press against a protruding dial stud (see 2 studs on rear of dial below).

rear of dial.jpg

Link to comment
Share on other sites
watchweasol Distinguished Member

watchweasol

Posted
Posted

Hi as Gary pointed out both the dial feet are missing. There are several repair techniques available to restore the feet. There are stick on feet (avaiable from Cousins UK ) but with calendar complications you have to watch for the clearance. There are tools available to recess the dial to relocate the feet. The one below is a Cousins one but they are available from Ali Express far cheaper.  The other alternative is to re-solder new feet on,  like the attached which is my own that I built a while ago or the commercial alternative.

d58711_pic3_cmyk.jpg

DSCF3258.JPG.4fc73ff07a2632e67c70032771430121.jpg

Link to comment
Share on other sites
grsnovi Distinguished Member

grsnovi

Posted
Posted

Unless the watch has sentimental meaning to you - you might want to find a new dial.

There are several watches that appear to have a similar dial here however you would really need to know more about your watch, dial size and specific movement to ensure that any dial you get would align properly with the holes in the main plate.

Disclaimer - I have never purchased from India and have seen too many stories that suggest it isn't a great idea.

Link to comment
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Restore formatting

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

×
 Share
Go to topic listing


  • Recently Browsing

    • No registered users viewing this page.

  • Topics

  • Posts

    • ManSkirtBrew
      Accutron 218 transistors

      By ManSkirtBrew · Posted

      As is tradition, one step forward, two steps back. Got the board populated and soldered into place without any issues.   But no hum. So I started testing the coils with an ohmmeter. I got 5.84k ohms across D1 (from red to red in the picture below), which is as expected. But I'm getting an open circuit for the other drive coil and feedback coil, D2 and F1 (from green to each of the two yellows).   Since the movement was working with my breadboard setup, it implies I somehow broke the connection between the coils and the solder lugs. They're all the way at the bottom of the lugs, but maybe the heat migrated down and broke the connections? I guess it's possible it happened while cleaning the flux off, but I used a soft artist's brush and isopropyl alcohol. I did a lot of high magnification examination, and I don't see any issues, but let me know if you see anything I missed or if you can think of anything else I should check.
    • GuyMontag
      Watch of Today

      By GuyMontag · Posted

      1947 NOS Ambassador 'C'. Actually, the case came without the movement so the movement isn't NOS, but she sure is pretty.
    • watchweasol
      AS2063 - hand setting

      By watchweasol · Posted

      Hi attached is the AS 20XX. Service sheet although there is no 2063 mentioned it may be of some use to you AS_AS 2060,1,2,6,4,6.pdf
    • JohnR725
      Epilame / Fixodrop

      By JohnR725 · Posted

      one of the problems we have is visible versus invisible. For instance millennium disulfide another high pressure lubricant black in color. I was told by somebody worked for the Boeing company that they had a piston like device somewhere that has eight call it around it to grab it so it has to slide and in the collet has to grab. But if somebody puts that type of dry grease on where grease with that in it it embeds itself basically in the metal and they have to throw the whole part away they get use it all. So I suspect on all the dry powdery lubricants that they will go into all the basically microscopic cracks and crannies of the metaland that's where it is visually at least until you scrub it off your visually going to see it which is good because you want your lubrication the stay word is. But I'm sure it doesn't last forever on the metal it's just a really nice lubrication  
    • GuyMontag
      Seiko 6601 Tech Sheet?

      By GuyMontag · Posted

      Thanks for the info. I can't seem to find tech sheets for those either.  I'll muddle my way though 🙂
×
×
  • Create New...