Jump to content

Seiko 5 Quartz???


Recommended Posts

Hi Everyone,

A friend asked to check his Seiko 5 watch that was a non-runner. To my surprise it was a quartz movement that apparently was expose to water.

Although, probably it is a fake Seiko, I was able to fix it after washing and reassembling.....

Any opinion about real or fake piece is appreciated.

Thanks

PHOTO-2022-03-06-13-08-55.jpg

PHOTO-2022-03-06-13-09-02.jpg

PHOTO-2022-03-07-14-21-59.jpg

PHOTO-2022-03-07-14-22-25.jpg

Screen Shot 2022-05-18 at 18.57.28.png

Link to comment
Share on other sites

7 hours ago, Kepas said:

Hi Everyone,

A friend asked to check his Seiko 5 watch that was a non-runner. To my surprise it was a quartz movement that apparently was expose to water.

Although, probably it is a fake Seiko, I was able to fix it after washing and reassembling.....

Any opinion about real or fake piece is appreciated.

Thanks

PHOTO-2022-03-06-13-08-55.jpg

PHOTO-2022-03-06-13-09-02.jpg

PHOTO-2022-03-07-14-21-59.jpg

PHOTO-2022-03-07-14-22-25.jpg

Screen Shot 2022-05-18 at 18.57.28.png

Strange that anyone would want to fake a 100 quid  Seiko 5, but this does seem to be the case. I was going to say a watch from parts but the dial says different.  The 5 that Seiko puts on their dials indicates 5 attributes to that range. Though opinions of these attributes do vary some of them are always stated. An automatic is one such attribute clearly here this is not present. Day and date complication is another so this must be a fake dial. Others are water resistance and recessed crown, other opinions are diashock system and crown at four. Seiko themselves state a robust case and braclet. Lets test that therory here shall we with a lump hammer, same fate that should befall all fake watches 🙂

31 minutes ago, Neverenoughwatches said:

Strange that anyone would want to fake a 100 quid  Seiko 5, but this does seem to be the case. I was going to say a watch from parts but the dial says different.  The 5 that Seiko puts on their dials indicates 5 attributes to that range. Though opinions of these attributes do vary some of them are always stated. An automatic is one such attribute clearly here this is not present. Day and date complication is another so this must be a fake dial. Others are water resistance and recessed crown, other opinions are diashock system and crown at four. Seiko themselves state a robust case and braclet. Lets test that therory here shall we with a lump hammer, same fate that should befall all fake watches 🙂

As regards to making it run again, a new movement is very cheap to replace as Kalanag has said. But if you fancy an hour or so to service it is possible you may get it to run if the cmos is ok. The main culprits of these cheap movements would be battery leak damage to circuits although repairable barring the cmos. Would i repair that ? If i had it in my head to do it for fun and a few hours to spare then maybe. Another would be a debris laden rotor, quite easy to clean up. But I have seen rotors in an almost disintegrated state. Another might be the coil, although these are usually damaged by someone poking around looking for a fault. Or you just might be really lucky and it needs cleaning out and servicing. If you are set on repairing it and your friend is sentimental about it then give service or repair a go. A couple of  simple tech testers will ease that operation. The Quickest route is to swap out the movement, you should find them easily, i think i may even have one or two kicking around. And if non of that seems fun then i suggest two of these 🏸  a temp rigged up net one fake watch and a few beers with your mate. Way more fun 👍

Edited by Neverenoughwatches
Link to comment
Share on other sites

Hi,

Thanks everyone for your opinions, although I was suspecting that the watch was a fake, I just wanted a more knowledgeable opinion here. I do agree with Neverenoughwatches that this piece doesn´t have  any of the Seiko 5 attributes (https://www.seikology.net/blog/the-history-of-seiko-5), therefore, it is a fake beater, probably as Watchweasol said a Mumbai special (surprisingly, I´ve seen several around here). I do agree with most of the opinions that the cheap movement make it not worth the hassle to fix it, but I have a lot of fun doing it and learn some, so for me it was worth it. Second quartz movement in my hands, the first one an Omega 255.411... that took me a while since it has the wrong minute wheel. Hopefully, there was a wonderful tutorial with images in this forum, that allows me to note the wrong wheel.

Thanks a lot.

IMG_0530.jpg

Untitled.jpg

  • Like 2
Link to comment
Share on other sites

  • 2 months later...
On 5/19/2022 at 1:39 AM, Neverenoughwatches said:

The 5 that Seiko puts on their dials indicates 5 attributes to that range. Though opinions of these attributes do vary some of them are always stated. An automatic is one such attribute clearly here this is not present. Day and date complication is another so this must be a fake dial.

I have also read this from other sources.  I believe that the day and date are always within the same window.  At least I have never seen otherwise. 

Link to comment
Share on other sites

Does that mean its a Feiko?  Sorry, I'll get ma coat.

I've also been the victim of the mumbai special too.  It was a ricoh something or other. The thing is that when it was opened up, it was actually an automatic, at least the parts resembled those of an automatic, but it was so rough and badly put together that here was no point in even trying to practice on it.  A lesson learned.

Link to comment
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Restore formatting

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.



  • Recently Browsing

    • No registered users viewing this page.
  • Topics

  • Posts

    • I also see a bit of danger for the wheel, at least you have to keep away from it and may get a too thick rest ring. My rest rings are about 0.05 mm. Better way would be a grinding wheel touching the staff with its circumference. Frank
    • Not easy to find this one everywhere,  so it depends where you are located. Joining it back together might be possible, i have silver soldered mild steel before even with traditional plumbers lead and its a pretty strong joint, but bere in mind this is only 1mm diameter.  The join would need to be very accurate,  it not something i have heard of anyone trying before. The part no 401 is the swiss code number and relates to watch winding stems in general
    • Thanks everyone for your helpful replies. I think between us we’ve worked out what’s going on. Next job is to have a proper look at this great wheel assembly, see if I can remove the clip and the friction fit pinion, give the bits a good clean, then put it back together with a bit of blue grease. I’ll also get the pallet fork under the microscope to see if it’s ok or been damaged. 
    • The cannon pinion (be it conventional style or what you see in this movement) should slip on its arbour so the hands can be set independently without affecting the gear train.  If there is too much friction between the cannon pinion and the second wheel, turning the hands to set them backwards can sometimes force the escape wheel teeth to overrun the pallet stones, creating the behaviour you describe. The train is running in reverse when this happens.  This can often chip the pallet stones. I’d say at least half of the watches I’ve inspected with very tight cannon pinions had chipped pallet stones. Hopefully this isn’t the case with your watch.  I’m not familiar with this movement but you need to get the friction in the cannon pinion adjusted correctly.  Hope this helps, Mark
    • Pallet fork was in. I’d had the movement running ok, and only removed the balance to flip it over and install the keyless works and date mechanism. The pallet fork wasn’t locking the gear train when hand setting - it was oscillating as the escape wheel rotated. This may have been in one direction only - can’t remember. 
×
×
  • Create New...