Jump to content

Cuckoo clock music box repair

LittleWatchShop

By LittleWatchShop
in All Things Clocks

 Share

Recommended Posts

LittleWatchShop Distinguished Member

LittleWatchShop

Posted
Posted

Well...it had to happen eventually.  A friend asked me to repair her Cuckoo Clock.  I repaired many when I was doing that work for my Dad eons ago.  Time to refresh my memory.

The first issue I found was this music box movement.  As you can see. the nylon gear is split.  I wonder if I should try to repair it or replace the governor unit like with the one here.

As far as the clock movement, my plan is to clean it in my ultrasonic.  Should I use my L&R ammonia-based watch cleaning solution or something else?

2021-10-11 13_04_13-20211011_125027.jpg ‎- Photos.png

music box gear.png

LittleWatchShop Distinguished Member

LittleWatchShop

Posted
  • Author
Posted

Latest update.  I got a replacement governor hoping that it would match up.  Well...it did not. It was close, but no cigar!!

I took the nylon gear off of the new governor and put it on the old one.  However, the diameter of the shaft was a few hundred microns off (the old shaft was smaller).  So, I put the nylon washer on and shimmed it with peg wood.  It was good enough.  The pitch of the gears needed to match the spinner, so that had to be moved over as well.

Got it to run after numerous eeky-tweaky adjustments.  HOWEVER!

It runs too fast.  I think the mass of the original spinner was greater.

I think I am going to put a solder blob on each blade to give it some additional mass.

Anybody on this forum gonna jump through the screen and grab me by the neck???

LittleWatchShop Distinguished Member

LittleWatchShop

Posted
  • Author
Posted

Here they are mounted.  Since the minute hand uses a bushing, the fit was straightforward.  I printed in black because that is the filament I have loaded.

You notice that the upper circle is not open in the print.  That is because of the resolution.  I need to make that hole bigger for it to print properly.  Frankly, the lower one as well.  But, these are temporary anyway.

2021-10-18 09_56_59-20211018_095458.jpg ‎- Photos.png

  • 1 year later...
Roughrider New Member

Roughrider

Posted
Posted

It appears I have the identical clock because the layout and components surely look identical. I also have a very similar problem with my music box. I'll try to show it in an attached photo if it posts. In my case, the lever comes down, lifts the hook out of the music spool stop hole, and the fly stop with it's tubing holding the fly gets out of the way. It plays, but not twice. The hook is out of the hole, the tubing releases the fly and the wire fly stop is out of the way. But the fly stops by itself. Nothing is holding it. If I nudge it, it will spin and the music plays normally. The it stop again. Can this be a lubrication problem? I've ordered some Liberty oil.

No luck posting photo.

oldhippy Distinguished Member

oldhippy

Posted
Posted

With any type of Cuckoo clock when it comes to striking the action depends on wires working correctly, they should not be bent in any place apart from the proper places, if not they will cause all sorts of trouble such as the cuckoo clock door not working properly, strike side playing up and causing God know what. A tiny drop of oil to stop rubbing of wires will help the action to work smoothly. The same goes for these musical types.   

  • Like 1

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Restore formatting

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

×
 Share
Go to topic listing

  • Recently Browsing

    • No registered users viewing this page.

  • Topics

  • Posts

    • Michael20
      French drum novice

      By Michael20 · Posted

      Regarding the spring winders, I made my own and used copper pipe reducers as the tubes to retain the spring. You will need to cut out a section for the end of the spring to protrude but if you watch one of the many videos on this subject that will make sense. You can find a selection of sizes on Ebay for very little cost. I'll attach a pic showing one of mine.  Good luck!
    • JohnR725
      Omega sweep second pinion friction spring - correct tension IS important

      By JohnR725 · Posted

      There were things bothering me about this discussion that took me a while to figure out the problem. In the image below it appears to be the spring may be pushing up? Normally when Omega has a spring pushing up the pinion has a pivot with a bridge to hold it in place so in other words the spring can push on something that stationary as opposed to this which appears to be floating? To understand the problem with the above image we need another image of side view which I have below. In my image down below on the left-hand side it agrees with the image up above. But the only problem is the left-hand side is defective and the right-hand side image is the way it's supposed to look. Then Omega if you can access the right documents does explain how and why this problem occurs. With the pinion floating around it might be assumed that you support it when putting on all the hands but you do not because as noted below if you do this small bush on the pinion will relocate out of position exactly what we see in the image up above.   Then Omega does not mention this but there is a possibility of also damaging the pinion and causing the bush to move to where it's not supposed to be when removing the hands.   
    • LittleWatchShop
      Regulating is too touchy

      By LittleWatchShop · Posted

      Maybe show us 1) the watch, 2) timegrapher readings in DU, DD, PU, and PD.
    • Louis1969
      Regulating is too touchy

      By Louis1969 · Posted

      The timegrapher displays significant beat error variations in the dial-up position. When the watch is lying flat (face up), the beat error is much higher than in other positions. Beat error readings are inconsistent, with especially large gaps in the face-up position.  Please help !  
    • Geotex
      Informational universe.

      By Geotex · Posted

      Looks like an open-access journal that runs as a glorified pre-print server with no true peer review, so it’s not easy to judge the veracity of the conclusions.
×
×
  • Create New...