Jump to content

What is the difference between the hand setting "pen"-style tools vs the larger bench-style tools?


GregG

Recommended Posts

Sometimes when installing hands, I don't feel confident with the loose approach to using the pen-style pressers, since you have to trust that your hand is steady, and slipping could be potentially dangerous to the movement.  I'm looking into the more bench-style tools for stability and its ability to press downwards exactly at 90 degrees, but can't find a resource that describes the difference between the two.

Link to comment
Share on other sites

When I was in school last century we pressed hands on with tweezers, preferably nickel or brass. Then towards the end of school a specialist came to teach us chronographs and the first thing we did was make our own nylon pushers from rod- that was a revelation and I've used those or commercial "free hand" plastic tipped pushers since. But I do see the advantage of the devices that keep things nice and vertical and even approaching "codger" status I think I'll buy one just to add to the arsenal. At a hobby level I think you could put your money toward more useful tools though.

  • Like 2
Link to comment
Share on other sites

  • 1 year later...

Just to add my two cents, I find the vertical tool usually gives a better result especially if the hands are not damaged. In addition to this the tool also forces you to slow down and set up the tool and position of the watch correctly. After a long challenging build and I see the finish line in sight I sometimes rush the final stages and end up taking several steps back (bending a hand, scratching the dial, slipping and dropping the entire movement on the floor)....setting up the hand press tool with the correct nib forces you to take your time. However, if the hands are not perfect sometimes you may need to apply a very small force at something other than perpendicular in order to lift or drop the hand very slightly (fractions of a mm) to avoid it clashing with the hand above or below or the dial chapters etc., and this is best done with the hand pen type tools as you get more of a feel of what is going on. Therefore, I usually force myself to use the desk type tool and then make fine adjustments with the hand tools if required, but as @nickelsilverpoints out you could manage with either tool.

Link to comment
Share on other sites

I like to install hands under a microscope. I find that the plastic tipped pens block the view and I can't see anything through the microscope. My spring loaded presser is collecting dust in the drawer.

So, I discovered that there is an Indian made tool from Anchor, that is basically a metal rod with a hole at each end. The watch hand hole is visible through the hole of the presser. But most of the time, I just press it on with a plastic tipped tweezer.

Link to comment
Share on other sites

Through trial and error I find that I get the best results by aiming my camera at the dial and viewing on my monitor. One time I was able to see why two hands were hitting one another and it wasn't because the hands were not set properly but because of corrosion on the underside of the minute hand which was scraping along the hour hand.

 

hand-press.jpg.7dcf444deb67d157fc1ba40f2953fc5a.jpg

  • Like 1
Link to comment
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Restore formatting

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.



  • Recently Browsing

    • No registered users viewing this page.
  • Topics

  • Posts

    • Thanks everyone for the replies. It seems setting the hand is a bit of a guessing game, and I thought there would be a very specific way to do it. Since the reserve indicator hand moves clockwise as the spring is wound, I tried setting it right at the start of the black side. But setting it there doesn't really make sense, because by the time the spring is halfway wound, the hand is only at the end of the red side... In my head halfway wound shouldn't mean the hand is still "in the red."
    • Lovely part of the country! I spend most of my days driving along the A64 for work in and around York. I'll be sure to drop plenty of questions soon! I've actually got a couple of watches on the way that I'm pretty sure I'll need some help with! They look pretty beat up from the pics but I love a challenge and an excuse to buy more tools 🤣
    • I have two of these in my home. You need to remove the movement from the case, take off the hands and remove the dial and take a few good photos of the front plate so I can see what the problem is. The round nut unscrews and the hands pull off pull them off from the center and not the tips as you could break them. 
    • I asked the question of one of the sellers. Its for removing the pins and making the holes in motorbike drive belts. God knows why they were both in two seperate joblots of watchmaking tool, thats bizarre. I haven't posted your setting lever steel yet mike, been busy with my mum past few days and had a locked myself in at home lazy watch repair day today 🙂 but I'm out tomorrow so i will get it off to you then. 
    • Hi everyone, I tried looking for answers on this online but came up with nothing, so I'm hoping some of you knowledgeable people might be able to help. I have an Elliot clock that has been in my family for at least 4 generations. I recently enherited it, and I'm trying to get it to run properly again, as it's been neglected a bit.  Here,s the problem. These clocks have a silencer mechanism, which is supposed to stop it from chiming between 11PM and 7AM but for some reason mine is silent between 1AM and 9AM. I have tried figuring out how to adjust it but have not managed. Does anyone have any idea on how to correct this? Please find attached some pictures of the clock. Thank you!
×
×
  • Create New...