Jump to content

Searching

Graziano
 Share

Recommended Posts

AshF WRT Addict

AshF

Posted
Posted

Ok so the other night I lost a yoke spring.  I had properly unloaded it with a safety pegwood holding it down, then when I tried to remove it it just disappeared.  I didn't even hear it skid or hit anything.

After an hour on the floor I gave up and continued disassembly.

At about 1:30am it was time to go to bed.  But I gave it one more look.  I did the trick of turning all the lights off and holding my mobile phone light up to my eye.  I found, 2 pieces of bent wire - unrelated.  1 pinion from another watch and finally my spring.  All in the space of 20 minutes.

Link to comment
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Restore formatting

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

×
 Share
Go to topic listing


  • Similar Content

  • Recently Browsing

    • No registered users viewing this page.

  • Topics

  • Posts

    • watchfellow
      Venus 178 hour counter creep

      By watchfellow · Posted

      Hi everyone, I put together a Venus 178 recently, but found that the hour counter "creeps" ie. runs when the chrono is disengaged. This is the similar type of setup as the Omega 861, where the hour counter is driven off the mainspring barrel, but stopped when the chrono is disengaged by a friction spring.  Am I correct in assuming that the friction spring for the hour counter driving pinion should be dry? I am guessing that the issue will be either the spring or the driving pinion, but while the driving pinion has some wear the spring looks decent.  I've attached a couple of photos in case anyone has any tips. Thanks in advance!
    • watchfellow
      Setting power reserve on LeCoultre Futurematic

      By watchfellow · Posted

      Thanks everyone for the replies. It seems setting the hand is a bit of a guessing game, and I thought there would be a very specific way to do it. Since the reserve indicator hand moves clockwise as the spring is wound, I tried setting it right at the start of the black side. But setting it there doesn't really make sense, because by the time the spring is halfway wound, the hand is only at the end of the red side... In my head halfway wound shouldn't mean the hand is still "in the red."
    • Chief
      Intro

      By Chief · Posted

      Lovely part of the country! I spend most of my days driving along the A64 for work in and around York. I'll be sure to drop plenty of questions soon! I've actually got a couple of watches on the way that I'm pretty sure I'll need some help with! They look pretty beat up from the pics but I love a challenge and an excuse to buy more tools 🤣
    • oldhippy
      Help - London Elliott Mantle Clock Night Silence

      By oldhippy · Posted

      I have two of these in my home. You need to remove the movement from the case, take off the hands and remove the dial and take a few good photos of the front plate so I can see what the problem is. The round nut unscrews and the hands pull off pull them off from the center and not the tips as you could break them. 
    • Neverenoughwatches
      What is this tool !

      By Neverenoughwatches · Posted

      I asked the question of one of the sellers. Its for removing the pins and making the holes in motorbike drive belts. God knows why they were both in two seperate joblots of watchmaking tool, thats bizarre. I haven't posted your setting lever steel yet mike, been busy with my mum past few days and had a locked myself in at home lazy watch repair day today 🙂 but I'm out tomorrow so i will get it off to you then. 
×
×
  • Create New...