Jump to content

Stem stuck as if completely wound ?? Working flawlessly until today ???

LittleWatchShop
 Share

Recommended Posts

LittleWatchShop Distinguished Member

LittleWatchShop

Posted
Posted

My Wittnauer chronograph which I have owned for the better part of my life suddenly exhibits strange behavior.

Short story:  I wound it yesterday (like everyday), it runs, today I went to wind it and the stem acted as though the watch is fully wound.  What could be wrong?

Longer story: This watch sits on my desk along with about seven other watches that I monitor daily.  Been sitting here for several months (previously it had been stored away in a jewelry box).  It has been working flawlessly until today.  I opened the back, but, alas, it is a chronograph.  I cannot see the rachet wheel or click.  I was going to release power and then rewind it but, like I say...cannot get access to this stuff.

My watchmaking renaissance is in its infancy. I have repaired several watches in the last couple of weeks and only lost a couple of components (grrr!!!).  I am many months (years) away from tackling a chronograph.  I will probably take it in for repair unless someone on this forum can share the magic bullet.

Thanks in advance!

Link to comment
Share on other sites
nickelsilver Distinguished Member

nickelsilver

Posted
Posted

The Valjoux 23 and 72 and their cousins all suffer from weak ratchet wheel teeth. A tooth can break at any time; I am thinking that on the last winding a tooth came off and is now jamming things. The click is just barely visible through a hole to the left of the chrono castle wheel viewed as in the pic if you want to try to let the power down, but it will need full disassembly to get to the ratchet wheel.

  • Like 1
Link to comment
Share on other sites
LittleWatchShop Distinguished Member

LittleWatchShop

Posted
  • Author
Posted

Just a follow up on this issue.  When I engage the crown, slowly turning in the winding direction, I feel the engagement and the resistance of the click.  So, I hypothesize that the winding wheel is engaging the rachet wheel.  Could still be a broken tooth lying around blocking the rachet wheel from turning.

I have three choices: 1) take it to a professional to have it fixed, 2) practice for a year and then tackle it myself, 3) do nothing.

Link to comment
Share on other sites
LittleWatchShop Distinguished Member

LittleWatchShop

Posted
  • Author
Posted
5 minutes ago, watchweasol said:

Hi what you must remember when doing any dismantling work is to photo each stage it will give you a record of what you did and where the parts all fit, memory is a fickle thing.

AMEN to that brother!!!  I have been doing that, albeit a little carelessly.  Gonna be very detail oriented going forward.  In the video posted, the watchmaker noted returning screws to their position after removing respective parts--so as not to get screws and their locations confused.  This is very clever, I think.

I ordered the part today.  Still not certain I will attack it, but at least I will have the part on hand for me, or a skilled watchmaker.

  • Like 1
Link to comment
Share on other sites
 Share
Go to topic listing


  • Recently Browsing

    • No registered users viewing this page.

  • Topics

  • Posts

    • Neverenoughwatches
      Second hand watch market.

      By Neverenoughwatches · Posted

      Hello good watch folk ,I  just fancied a light hearted discussion after my head was starting to spin over Epilame 😅. Specifically I'm meaning the sale of vintage watches, say nothing past the 1980s market. The stuff we see on ebay and other similar sites and found at carboots, curio shops etc. And are  we thinking its reaching a peak volume ?  Younger generations clearing out passed parents and grandparents possessions.  The younger folk are not as sentimental as the old fogies ( I'm now nearly at an age that i used to think was old fogie age ). When might it have started ?  i often wish i discovered the hobby much much sooner when selling your grandfathers pocket watch at a boot sale for a few quid was just a way to offload some tat. And when might it slow down. Thoughts anyone ?
    • Neverenoughwatches
      Epilame / Fixodrop

      By Neverenoughwatches · Posted

      Yes i did eventually realise that the oil will act as a barrier, I'm sure the discussion will continue. Ive had two oleophobic coffees ( added coconut ) and in the meantime i have this just delivered to take my mind off epilame for the time being. My favourite type of dial, its a beautiful looking watch traditional English made and it runs,  the ticktock is phenomenal,  i can hear it across my living room .  You wont believe how much it was. Thats interesting about synthetic oils , i thought the same, going from a 2 year service to 5 years is a big drop in income for service folk.  I expect some did well when they embraced the use of synthetic,  probably drawing in more customers than those that didn't use the new fangled substances , i bet fairly short lived though. The more frequent service makes more sense to me, not for just the service but for the regular check up inspections that might pick up impending faults. As far as epilame goes, wouldn't it be great to be able to fumigate the complete movement in a sealed jar of heated stearic acid, 🤔 now theres a thought 😅.
    • Albyon
      AS2031-57E solar panel - mission: impossible

      By Albyon · Posted

      Imm going to close the discussion by attaching the photo of my super-titanium after several vicissitudes finally working. Purchased as not working I replaced the battery and for a stroke of luck I found its semi-new solar panel which, having verified its operation, seems to recharge the accumulator perfectly. I had taken this watch almost by bet, with 40 euros I brought it back to life. The initial half idea was to resell it to finance another purchase, but.. it's definitely a nice item. It would need to check the impermeability but it's a pleasure to see it on the wrist 😃
    • Albyon
      Insert the movement inside the case

      By Albyon · Posted

      In fact the secret is to go gently and find the way without forcing, and the movement enters without problems
    • Murks
      2813

      By Murks · Posted

      Yea a have given it a full service this movement is chinese 2813 whats the lift angle for this movement does anyone knows  and how  do a remove the default  of 52 degrees on my timegrapher?   Hi you said my lift angle is default how do a remove this from my timegrapher?
×
×
  • Create New...