Jump to content

Searching for a Seiko Crystal


Recommended Posts

As often asked and answered. There is no secret place for parts. The searches you can do are the same that all others here do - Internet, Ebay, well-know online material houses.

  • Like 1
Link to comment
Share on other sites

18 hours ago, Dave84 said:

I ended up finding one on ebay for £38 including postage

Congrats! Objectively it's still a lot of money for a crystal (you can get a great mechanical Russian watch for that money), but for a watch that means a lot to you, £38 can still feel like a bargain.

Edited by VWatchie
  • Like 1
Link to comment
Share on other sites

you dont always need an original,  measure the old one, I can see from the part number its 30mm and probably is a tension ring too so you can get a generic one for less than £10.00 that will do the same job. 

I have done this one many plain Seiko crystals even glass ones. 

Link to comment
Share on other sites

1 hour ago, MyRetroWatches said:

you dont always need an original,  measure the old one, I can see from the part number its 30mm and probably is a tension ring too so you can get a generic one for less than £10.00 that will do the same job. 

Are you sure? Picture from the Ebay listing of someone asking $78 (!!) for it.

s-l500.jpg

With it's large bezel and domed shape is not a good candidate for generic replacement. And it happens, beginners and amateurs aren't able to swap a bezel or tension ring from a crystal to another.

And here's how anyone can decode (up to an extent) Seiko crystal codes Crystal Codes.pdf

Edited by jdm
Link to comment
Share on other sites

  • 3 weeks later...

Hi Guys, just a quick update, again thanks for the responses. 

Just wanted to add a quick pic of the new crystal which came fixed within a retaining ring which sat beneath the bezel ring.

Cheers

Dave 

IMG_20200806_140836_BURST001_COVER.jpg

  • Like 1
Link to comment
Share on other sites



  • Recently Browsing

    • No registered users viewing this page.
  • Topics

  • Posts

    • Hi All, my watch - raketa (2624 movement) Now the escape wheel can't move itself. If i blow air to balance wheel, the second hand can move .  https://drive.google.com/file/d/1ykpAf63N2BUtvVVu1jra0p9hZP4xh9d-/view?usp=drive_link I have reinstall the click from mainspring barrel and the setlever and clutch lever. The other parts is unchanged. is it a problem about release all energy of the mainspring? How can i restore it?  
    • Here's a size chart. 40mm is about 17¾L. I looked in Bestfit but couldn't find anything close.   
    • I've started trying to use the Betfit, but I don't know which measurement I must take for the caliber. The diameter of the dial side is 40mm, and the other side 36,5mm 🤔.
    • I'm currently 3D printing a new basket and trays for my Pearl machine - I printed one last week in PETG material and it worked well at first. I had taken a calibration cube and soaked it in old cleaning fluid for 8 weeks and then measured it, and there was no discernable swelling or shrinkage and the cube seemed mechanically intact. All went well after the cleaning cycles and then onto the drying cycle..... that's when things went awry. The heat was more than I was expecting and the basket and individual trays warped and deformed, I later found out that PETG is rated to 65°C working temperature (PLA = 54°C) I am now trying to print from nylon (working temperature = +/- 100°C, depending on the specific blend) - but it is extremely difficult to print with, my third attempt is chugging away now while I am at work - hopefully I don't go home to a ball of wool like last time!  Assuming the heating compartment can't go higher than 100°C.... but not second guessing myself...anyone have any ideas or measured it? I also have a question on the trays, maybe I'm not seeing the obvious, but how do you use the ones identified with the arrow? they are called  Basket_for_large_mainplate_and_mainspring.stl Basket_for_small_mainplate_and_mainspring.stl I can see the place for the mainplate, but how are you supposed to place the mainspring, you can't uncoil the mainspring to fit around the outer circumference of the tray or else you would damage the inner tight coils. Is the idea that you supposed to lay it on top of the mainplate?
    • It is possible to true the pearl basket to run better takes a good hour of filing though.
×
×
  • Create New...