Jump to content

French travelling alarm clock balance

Mugsey

By Mugsey
in All Things Clocks

 Share

Recommended Posts

Mugsey New Member

Mugsey

Posted
Posted

Hi all have just joined this forum wondered if any one could help me in locating a balance for this little french travelling alarm tree is no name on the movement so would appreciate any info. I have seen several of a similar nature but don’t no I should be asking for the diameter of the balance is approx 14 mm which looks more like a watch balance

thanks

707C8943-5906-453C-B604-22F1939D69CD.png

Link to comment
Share on other sites
watchweasol Distinguished Member

watchweasol

Posted
Posted

Hi Can you please post some pictures of the workings of the clock and the balance in particular.   It is most likely a platform escapement and if so is replaceable as a unit if the spares are available.  But we need to see the movement  before deciding on a courese of action.   Thank you 

Link to comment
Share on other sites
watchweasol Distinguished Member

watchweasol

Posted
Posted

Hi  Thank you for the pictures,  Its not a platform escapement in the traditional sense,  I doubt very much if spares are readily available .   If the balance staff is broken it is most likely to make one  or have one made.  or alternativly try and source an donor unit to cannibalise the parts.

Link to comment
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Restore formatting

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

×
 Share
Go to topic listing


  • Recently Browsing

    • No registered users viewing this page.

  • Topics

  • Posts

    • VWatchie
      Epilame / Fixodrop

      By VWatchie · Posted

      Yes and no. I use Moebius 9501 synthetic grease and it is significantly runnier than the Moebius 9504 synthetic grease (and I assume Molykote DX) that I previously used. I haven't seen 9504 spread and it is in my opinion the best grease money can buy. However, my current method of cleaning doesn't remove it from the parts, so that's why I have decided to use the 9501 instead. I believe I read somewhere that Molykote DX too is difficult to clean off. Thinking about it, I'm pretty sure my 9501 grease which expired in June 2022 is runnier now than it was when it was new, but whether new or old it always needs to be stirred before use. So, that's why I treat the parts of the keyless works, cannon pinion, etc. with epilame. That was very thoughtful of you and something that had completely passed me by. Not sure what the epilame will do when it wears off in a non-oiled hole. Anyone?
    • watchweasol
      Seiko 6601 Tech Sheet?

      By watchweasol · Posted

      Hi not found one either yet,  close relative is the 436 and 4361 according to ranff.db.   It gives quire a lot of detail but not as good as the old site.      RANFF.DB.
    • nevenbekriev
      Rolex 2235 escape wheel jewel setting replacement

      By nevenbekriev · Posted

      No problem to replace the setting with the staking set. Press the new setting from inside, use flat face punch with hole. The punch must be wider than the setting, the hole to be as not to press at the stone, but only on the bush. Press by hand until the setting gets flush with the plate surface, so the punch must rest on it.
    • nevenbekriev
      Quarter repeater mainspring thickness

      By nevenbekriev · Posted

      Yes, the arbor usually makes about 3 to 3.5 turns. But usually spring takes 2/3 to 3/4 of the free space in barrel, not 1/2, so take it for the calcullations. This way the change in torque is smaller. I have a picture for You, this one is little older, but no mater
    • noirrac1j
      Rolex 2235 escape wheel jewel setting replacement

      By noirrac1j · Posted

      I overhauled a ladies Rolex and noticed erratic performance so I stripped in down again and did fault finding. This is what I saw. The lower jewel (the one in the plate) is cracked and the hole is too big. Before discovering this, I stripped down and re-cleaned the main-plate (and parts) by hand with a fine natural fiber brush. I somehow missed the fault the first time and cannot understand how it was still running. Perhaps re-cleaning it dislodged some pieces of the jewel widening the hole? I don't know. Now I need to replace the jewel but don't have a Seitz tool. The Rolex part is 2130-0913 and the top and bottom are the same. The part comes complete in brass setting with KIF elastor spring and cap jewel. Note: I have never replaced a jewel. I do have a good vintage stacking set that I've used quite a bit.  Can I replace using a stacking set? Any suggestions would be greatly appreciated.  
×
×
  • Create New...