Jump to content
watchweasol

Balance spring needles

Recommended Posts

 Hi  A short while ago there was a mention of re forming and adjusting balance springs. I mentioned I had made some tools from sewing needles with the eye ground down providing a fork with witch to adjust the springs. I used two sizes of needle, put in a pin vise and just stoned the end off. Done carefully they make usefull tools. Mine are just fitted into to old chopsticks and being square they don't roll about the bench.    A sewing machine needle fitted into a handle also gives a good stiff tool for manipulating small parts and inspecting train wheels etc.  These are not expensive to make in either time or materials but I wouldn't be without them.   

DSCF3269.JPG

DSCF3270.JPG

DSCF3271.JPG

Share this post


Link to post
Share on other sites

Great tips . i am going to make a couple of those . I though about this for a while. I often need to fix the balance spring to get it running perfect. I have a 5 mm plastic rod that would work as a handle instead of te chopstick 

Share this post


Link to post
Share on other sites
12 minutes ago, rogart63 said:

Great tips . i am going to make a couple of those . I though about this for a while. I often need to fix the balance spring to get it running perfect. I have a 5 mm plastic rod that would work as a handle instead of te chopstick

There are manufactured fork end needles. I see if I can take a magnified picture of one to post. 

@rogart63  PM sent to you on different subject, please check your inbox.

Share this post


Link to post
Share on other sites

Sewing machine needles, of course.

Brilliant idea.

 I had thought of using ordinary sewing needles, but sewing machine needles, since they have a flat face ground on them are perfect. I may even fabricate a couple of 3d printed handles so I can slot them right in.  My wife is a quilter, so now I have a use for the old needles when they get dull or break, rather than discarding them.

Something else for the to-do list when I get back.

Share this post


Link to post
Share on other sites

I made one tonight But didn't check the size. U need a very  thin needle. The thinnest you can find. 

The one i made i can use for pocket watches maybe.  Make a new one tomorrow  if i can  find a small enough needle. 

Share this post


Link to post
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

Loading...

  • Recently Browsing

    No registered users viewing this page.

  • Topics

  • Posts

    • How to remove stem  from Seiko 8c23-6059 I believe stem=354 351 back of watch reads 8c23-6059   564384
    • Thanks. I'm also seeing a no lubrication symbol for the corrector wheel. I see in mark's video that he lubricated the elongated hole for this wheel. Does lubrication go there? Or is there absolutely no lubrication for this component. Another question regarding reversing wheels. On a diagram I see in another thread it also shows no lubrication to be applied on the teeth or pawls whereas in mark's video he applies lubrication on the teeth. Is his procedure incorrect? What is the purpose of requiring epilame on these if no lube is applied here? Also the diagram does not show lubricating the date jumper on the part that indexes the date wheel. Should this area be lubricated like many other manufacturers do? Or is this not necessary?
    • I have replaced the capacitor in this JDM Seiko AGS Spirit Titanium (5M22 movement). This is a one piece case, so the bezel has to come off to get to the movement. The bezel gasket was a bit hard to get back in (ordered two new ones and ruined one), but it all went in on the second attempt (using a drill press. Yes, I am a newb and do not own a crystal press. But I have other tools and am resourceful). Here it is. I really like this watch. It's very well made, the titanium case and band make super-light and very comfortable watch. The crystal is most likely sapphire, though it does not say so on the back. I did look up the Seiko catalog and it calls for sapphire replacement part. Also, for a watch this old (from the early-mid 90's) the crystal is literally pristine. No scuffs or scratches. Very high quality piece that I am really enjoying right now. The new style capacitors (LiOn batteries, really) allow about a 4 month reserve on these. I am very happy with the purchase and the "service" I gave it. Before serivice b   After service    
    • Watches of this vintage  could be of either  2209 or 2409 variety. The 24 series is still being  produced  and new parts are still available  from meranom  in Russia. The  22 series is archaic  .parts must be cannibalized  from  other  movements. These can be purchased  by the bushel online. CHEAP.
    • For some reason it won't play for me.but my first  reaction is excess wear in the area of the balance  staff. 
×
×
  • Create New...